LG AVNQ18GM1T1 Скачать руководство пользователя страница 20

Страница: 20 / 24

ENGLISH

INSTALLATION INSTRUCTIONS

Installer Setting - Installer Setting Code Table

Installer Setting Code Table

No.

Function

Function code

Setting value

Remote controller LCD

Mode override

0 : Set to master

1 : Set to slave

Ceiling height

Selection

1 : Standard

2 : Low

3 : High

4 : Super high

Group control

0 : Set to master

1 : Set to slave

2 : Check master/slave

Auxiliary heater

3 : Set to auxiliary heater

4 : Cancel auxiliary heater

5 : Check auxiliary heater Installation

Mode Override

This Function is only for Non-Auto Changeover H/P model.

Ceiling Height Selection

Indoor unit connected to wired remote controller operate as wired remote controller setting.

Auxiliary heater

This function is only applied to models with Auxiliary Heater function being activated.

Group Control (optional)

This function is only for group control. Please don’t set this function in case of non-group
control.

After setting group control of the product, turn off the power then turn it back on after 1
minute.

Содержание AVNQ18GM1T1

























Результаты поиска

Содержание AVNQ18GM1T1

Отзывы:

Похожие инструкции для AVNQ18GM1T1

Бренды по названию

Популярные бренды

LG AVNQ18GM1T1, Руководство по установке

Результаты поиска

Содержание AVNQ18GM1T1

Отзывы:

Похожие инструкции для AVNQ18GM1T1

Бренды по названию

Популярные бренды