manualshive.com logo in svg

LG AUUW09GAE(LUU097HV), Руководство по установке, Страница: 21 / 24

Поделиться
Скачать
LG AUUW09GAE(LUU097HV) Скачать руководство пользователя страница 21

Function   

Installation Manual 

21

ENGLISH

Night Quiet Mode with Mode Lock.

Mode Lock (Cooling) 
+ Night Quiet Mode (step 1)

Mode Lock (Cooling) 
+ Night Quiet Mode (step 2)

CAUTION
• If comp frequency and fan speed are down, the cooling capacity may

decrease accordingly.

• This function is only available for Cooling Mode.
• If you want to stop the Night Quiet Mode, Change the Dip Switch.
• If operating indoor unit is set by the fan speed  “Power”, Night Quiet

Mode will be stopped until fan speed “Power” is changed.

Setting Procedure

1. Set the Dip Switch as follow after shutting the power source down.

2. Reset the power.

Mode Lock with Night Quiet Mode

Saving Power Consumption with Mode Lock.

Mode Lock (Cooling) 
+ Night Quiet Mode
(step 1)

Mode Lock (Cooling) 
+ Night Quiet Mode
(step 2)

Mode Lock (Cooling) 
+ Saving Power
Consumption (step 1)

Mode Lock (Heating) 
+ Saving Power
Consumption (step 1)

Mode Lock (Cooling) 
+ Saving Power
Consumption (step 2)

Mode Lock (Heating) 
+ Saving Power
Consumption (step 2)

Only Cooling Mode

Only Heating Mode

Mode Lock

Содержание AUUW09GAE(LUU097HV)

























Отзывы:

Нет отзывов