LG AS-H246DGM0 Скачать руководство пользователя

Страница: 13 / 56

Installation

Installation

Indoor unit

• Do not have any heat or steam near the unit.

• Select a place where there are no obstacles in front of the

unit.

• Make sure that condensation drainage can be conveniently

routed away.
Do not install near a doorway.

• Ensure that the space around the left and right of the unit is

more than "A". The unit should be installed as high on the
wall as possible, allowing a minimum of "B" from ceiling.

• Use a stud finder to locate studs to prevent unnecessary

damage to the wall.

Outdoor unit

• If an awning is built over the unit to prevent direct sunlight

or rain exposure, make sure that heat radiation from the
condenser is not restricted.

• Ensure that the space around the back and sides is more

than 30cm. The front of the unit should have more than
70cm of space.

• Do not place animals and plants in the path of the warm air.
• Take the weight of the air conditioner into account and

select a place where noise and vibration are minimum.

• Select a place where the warm air and noise from the air

conditioner do not disturb neighbors.

Rooftop Installations:

• If the outdoor unit is installed on a roof structure, be

sure to level the unit. Ensure the roof structure and
anchoring method are adequate for the unit location.

• Consult local codes regarding rooftop mounting.

More than "B"

More than

"A"

More than 2.3m

More than

"A"

• Capacity is based on standard length and maxi-

mum allowance length is on the basis of reliability.

• Oil trap should be installed every 5~7 meters.

Grade

Clearance(cm)

24K

Pipe Size

Capacity

(Btu/h)

GAS

LIQUID

Max.

Length

(m)

Additional

Refrigerant

(g/m)

Max.

Elevation

(m)

Standard

Length

(m)

24k

5/8"(Ø15.88)

3/8"(Ø9.52)

7.5

If case more than 5m

Outdoor unit

Indoor unit

Outdoor unit

Indoor unit

Oil trap

Outdoor unit

Indoor unit

Selection of the Best Location

Piping Length and Elevation

Install the indoor unit on the wall where the height
from the floors more than 2.3 meters.

More than 30cm

More
than 60cm

More than 60cm

More than 70cm

- 13 -

LGE Internal Use Only

Содержание AS-H246DGM0
























































Результаты поиска

Содержание AS-H246DGM0

Отзывы:

Похожие инструкции для AS-H246DGM0

Бренды по названию

Популярные бренды

LG AS-H246DGM0, Руководство пользователя

Результаты поиска

Содержание AS-H246DGM0

Отзывы:

Похожие инструкции для AS-H246DGM0

Бренды по названию

Популярные бренды