LG 55LH85 - - 54.6" LCD TV, Руководство по обслуживанию

Страница: 14 / 76

Copyright LG Electronics. Inc. All right reserved.
Only for training and service purposes
5-3. Adjustment of White Balance
5.3.1 Automatic Adjustment
1) The adjustment condition should be set by the Power On
key.
2) Perform the zero calibration of the Color Analyzer and
place the probe close to the display center.
3) Connect the communication cable (RS-232C).
4) Select the desired model of the adjustment program and
perform the adjustment.
5) After the adjustment is ended (check the OK sign), check
the adjustment condition for each mode of the set.
(Warm, Medium, Cool)
6) Disconnect the probe and the communication cable to end
the adjustment.
* The adjustment should be started with "wb 00 00" and
ended with "wb 00 ff", and the offset should be adjusted
when necessary.
5.3.2 Manual adj. method
1) Set TV in Adj. mode using POWER ON
2) Press the ADJ of the R/C to enter into ‘EZ-ADJUST’.
3) Select ‘10.TEST PATTERN’ with the CH +/- key and press
the Enter key for 30 minutes or longer to perform the heat
run.
4) Perform the zero calibration of the Color Analyzer and fix
the sensor with the 10cm or less distance at the center of
the LCD module surface when adjusting.
5) Press the ADJ of the R/C to select ‘7.White-Balance’ of the
Ez-Adjust and press the right arrow key(
G
) to enter into the
adjustment mode. (As soon as you press ‘
G
’, the screen is
entered into the full white inner pattern.)
6) Fix one of the R/G/B gains to 192 and decrease the
remaining two gains to adjust not to exceed 192.
7) The adjustment is done at three white balances of Cool,
Medium and Warm
* Adjustment environment and reference
1) Environment illuminance
Adjust it to 10 LUX or less at the place where the light
source such as lamp should be blocked at maximum.
2) Probe location
: Maintain the Color Analyzer (CA-210) close to the
module surface by 10cm or less and keep the probe of
the Color Analyzer perpendicular to the module
surface (80°~ 100°).
3) Aging time
- Keep the power on after the aging start (with no power
off) to perform the heat run for 15 minutes or longer.
- Make sure that the back light is turned on by using no
signal and the full white pattern or others.
• Standard color coordinate and temperature using CS-
1000 (over 26 inch)
• Standard color coordinate and temperature using CA-
210(CH 9)
5.4 Option selection per country
(1) Overview
- Option selection is only done for models in Non-USA
North America due to rating
- Applied model: LA92A Chassis applied None USA
model(CANADA, MEXICO)
(2) Method
1) Press ADJ key on the Adj. R/C, then select Country
Group Menu
2) Depending on destination, select KR or US, then on the
lower Country option, select US, CA, MX. Selection is
done using +, - KEY
• TV
- Adjust directly if it's not a Wireless/Wired state
- Adjust after changing to HDMI5 on the Wireless/Wired state
• Media-Box
- Adjust on the Wireless/Wired state that is excepted the
HDMI5.
LGE Internal Use Only - 14 -
Mode Color Coordination Temp
∆
UV
x y
COOL 0.276 0.283 11000K 0.0000
MEDIUM 0.285 0.293 9300K 0.0000
WARM 0.313 0.329 6500K 0.0000
Mode Color Coordination Temp
∆
UV
x y
COOL 0.276±0.002 0.283±0.002 11000K 0.0000
MEDIUM 0.285±0.002 0.293±0.002 9300K 0.0000
WARM 0.313+0.002 0.329±0.002 6500K 0.0000