LG 50PG200R, Руководство по обслуживанию

Страница: 12 / 28

- 12 - LGE Internal Use Only Copyright©2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
O
DDC Adjustment Command Set
[ R/G/B GAIN max value : C0
9-4. Adjustment of White Balance for
Manual Adjustment
Adjustment mode: Two modes of Medium(Vivid) and Warm
(Cool data is automatically calibrated by the Medium data)
- Equipment : 1) Color analyzer(CA100+, CA210) should be
used in the calibrated ch by CS-1000(.(LCD :
CH9, PDP : CH10)
2) Adjustment remocon
- For manual adjustment, it is also possible by the following
sequence.
Operate the zero-calibration of the CA-100+ or CA-210, then
stick sensor to the module when adjusting.
(1) Select white pattern of heat-run by pressing “POWER ON”
key on remote control for adjustment then operate heat run
longer than 15 minutes. (recommend)
(If not executed this step, the condition for W/B will be
different)
(2) Changing to the AV mode by remote control.(Push front-
AV)
(3) Input external pattern(85% white pattern).
(4) Stick sensor to center of the screen and select each items
(Red/Green/Blue Gain and Offset) using
D
/
E
(CH +/-) key
on R/C..
(5) Adjust R/ G/B Gain using F / G (VOL +/-) key on R/C.
(6) Adjust two modes of Medium(Vivid) and Warm as below
figure.
(Fix the one of R/G/B and change the others)
1) Default : Medium(Vivid)
2) Push the “VOL +” key twice : Warm
[ Refer to the below case to know what value is fixed.
[CASE]
First adjust the coordinate much away from the target value(x, y).
1. x, y > target
1) Decrease the R, G.
2. x, y < target
1) First decrease the B gain,
2) Decrease the one of the others.
- In case of decreasing the x, decreasing the R : fix G
- In case of decreasing the y , decreasing the G : fix R
3. x > target , y < target
1) First decrease B, so make y a little more than the target.
2) Adjust x value by decreasing the R
4. x < target , y > target
1) First decrease B, so make x a little more than the target.
2) Adjust x value by decreasing the G
(7) When adjustment is completed, Exit adjustment mode
using EXIT key on R/C.
Adjustment
content
Aging On/Off
input select
R GAIN
G GAIN
B GAIN
R GAIN
G GAIN
B GAIN
R GAIN
G GAIN
B GAIN
CSM modo
EEPROM Read
EEPROM Write
No
1
2
3
4
5
6
CMD
(HEX)
F3
F4
16
18
1A
16
18
1A
16
18
1A
F2
E7
E8
ADR
00
00
00
01
02
00
00
00
VALUE
FF/00
00 - FE
00 - FE
00 - FE
00 - FE
00 - FE
00 - FE
00 - FE
00 - FE
00 - FE
00
01
02
00
data
Detail
OO : OFF
01 : ON
FF : WB Ready
0x10 : TV
0x20 : AV1
0x21 : AV2
0x23 : AV3
0x40 : Component1
0x41 : Component2
0x60 : RGB PC
0x90 : HDMI1
0x91 : HDMI2
0x92 : HDMI3
GAIN Adjsutment
CSM COOL
GAIN Adjsutment
CSM MEDIUM
GAIN Adjsutment
CSM WARM
COOL
MEDIUM
WARM
EEPROM read
EEPROM write
Color Coordinate
x y
0.293±0.002
0.329±0.002
9,300K
6,500K
0.000
0.003
0.285±0.002
0.313±0.002
MEDIUM
WARM
Mode Temp uv