LG 47LB58 Series, Руководство по обслуживанию

Страница: 17 / 23

- 17 -
LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved.
Only for training and service purposes
4.2.5. Adj. method
(1) Auto adj. method
1) Set TV in adj. mode using POWER ON key.
2) Zero calibrate probe then place it on the center of the
Display.
3) Connect Cable.(RS-232C to USB)
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sign), check adj. status pre
mode. (Warm, Medium, Cool)
6) Remove probe and RS-232C cable to complete adj.
▪ W/B Adj. must begin as start command “wb 00 00” , and
finish as end command “wb 00 ff”, and Adj. offset if need.
(2) Manual adjustment. method
1) Set TV in Adj. mode using POWER ON.
2) Zero Calibrate the probe of Color Analyzer, then place it
on the center of LCD module within 10 cm of the
surface.
3) Press ADJ key → EZ adjust using adj. R/C → 7. White-
Balance then press the cursor to the right(key ►).
(When right key(►) is pressed 204 Gray internal pattern
will be displayed)
4) One of R Gain / G Gain / B Gain should be fixed at 192,
and the rest will be lowered to meet the desired value.
5) Adjustment is performed in COOL, MEDIUM, WARM 3
modes of color temperature.
▪ If internal pattern is not available, use RF input. In EZ
Adj. menu 7.White Balance, you can select one of 2
Test-pattern: ON, OFF. Default is inner(ON). By selecting
OFF, you can adjust using RF signal in 204 Gray pattern.
▪ Adjustment condition and cautionary items
1) Lighting condition in surrounding area
Surrounding lighting should be lower 10 lux. Try to
isolate adj. area into dark surrounding.
2) Probe location
: Color Analyzer(CA-210) probe should be within 10 cm
and perpendicular of the module surface (80° ~ 100°)
3) Aging time
- After Aging Start, Keep the Power ON status during 5
Minutes.
- In case of LCD, Back-light on should be checked
using no signal or Full-white pattern.
4.2.6. Reference (White balance Adj. coordinate and
color temperature)
▪ Luminance : 204 Gray
▪ Standard color coordinate and temperature using CS-1000
(over 26 inch)
▪ Standard color coordinate and temperature using CA-210(CH 14)
4.2.7. ALELF & EDGE LED White balance table
- EDGE LED module change color coordinate because of
aging time.
- Apply under the color coordinate table, for compensated
aging time.
* Normal Line
[LN5xxx, LA6xxx, LA7xxx, LA8xxx]
*Aging Chamber
[LN5xxx, LA6xxx, LA7xxx, LA8xxx]
Mode
Coordinate
Temp ∆uv
x y
Cool 0.269 0.273 13000 K 0.0000
Medium 0.285 0.293 9300 K 0.0000
Warm 0.313 0.329 6500 K 0.0000
Mode
Coordinate
Temp ∆uv
x y
Cool 0.269 ± 0.002 0.273 ± 0.002 13000 K 0.0000
Medium 0.285 ± 0.002 0.293 ± 0.002 9300 K 0.0000
Warm 0.313 ± 0.002 0.329 ± 0.002 6500K 0.0000
NC4.0
Aging
time
(Min)
Cool Medium Warm
X y x y x y
271 270 286 289 313 329
1 0-2 283 287 298 306 322 342
2 3-5 282 285 297 304 321 340
3 6-9 281 284 296 303 320 339
4 10-19 279 281 294 300 318 336
5 20-35 277 277 292 296 316 332
6 36-49 275 274 290 293 314 329
7 50-79 273 272 288 291 312 327
8 80-119 272 271 287 290 311 326
9 Over 120 271 270 286 289 310 325
NC4.0
Aging
time
(Min)
Cool Medium Warm
X y x y x y
271 270 286 289 313 329
1 0-5 282 285 297 304 321 340
2 6-10 278 280 293 299 317 335
3 11-20 275 275 290 294 314 330
4 21-30 272 272 287 291 311 327
5 31-40 269 269 284 288 308 324
6 41-50 268 267 283 286 307 322
7 51-80 267 266 282 285 306 321
8 81-119 266 264 281 283 305 319
9 Over 120 265 263 280 282 304 318