LG 43LX774H Скачать руководство пользователя страница 66

Страница: 66 / 96

206-4309

Remote Jack Pack Setup

RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item

093

RJP AVAILABLE

appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE

to 1). See Installer Menu detailed descriptions for further information.

093 RJP AVAILABLE 001

TV Connections

Caution: Make these connections ONLY after Master TV Setup and TV cloning procedures

are complete. Also, make sure to use the RJ-45 Control cable from the RJP cable bundle to

make the connection to the TV’s RJP port. Do NOT connect a standard Ethernet cable to the

RJP port, as this may damage the TV and network equipment.

Refer to the figure below, and connect the RJ-45 Control cable from the RJP cable bundle to the RJP

port

on the TV’s rear jack panel. Then, connect HDMI and Composite Video/Audio connectors, as applicable,

for the cable bundle.

Reference: Remote Jack Pack / TV Connections & Setup

Note:

RGB is not supported on these TV models. If an RGB source is connected to a legacy

RJP, you will see a brief message on-screen to indicate that this device is not supported.

SPEAKER OUT

LINE OUT

PTC SERVICE

(SERVICE ONLY)

RJP Use Only

GAME CONTROL

/ MPI

L/MONO

AUDIO

COMPONENT IN / AV IN

ANTENNA /

CABLE IN

LAN

AUX LAN

OPTICAL

DIGITAL

AUDIO OUT

USB IN 2

VIDEO/ Y

PC AUDIO

RESET UPDATE

SERVICE

TV-LINK CFG

HDMI IN 1

Connect HDMI connector

from RJP cable bundle.

RJP Use Only

Connect RJ-45 Control cable

from RJP cable bundle.

Note:

Before connecting the

RJP cable bundle, you may

need to remove the gray RJP

cover that isintended to

prevent accidental misuse of

the port.

AUDIO/VIDEO IN

Connect Composite Video/Audio

connectors from RJP cable bundle.

(Composite Video on legacy RJP only.)

Содержание 43LX774H

































































































Результаты поиска

Содержание 43LX774H

Отзывы:

Похожие инструкции для 43LX774H

Бренды по названию

Популярные бренды

LG 43LX774H, Руководство по установке

Результаты поиска

Содержание 43LX774H

Отзывы:

Похожие инструкции для 43LX774H

Бренды по названию

Популярные бренды