LG 32LN5650 Скачать руководство пользователя страница 13

Страница: 13 / 69

- 13 -

LGE Internal Use Only

Only for training and service purposes

7. 3D function test

(Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4])

* HDMI mode No. 872 , pattern No.83

(1) Please input 3D test pattern like below.

(2) When 3D OSD appear automatically, then select OK button.

(3) Don't wear a 3D Glasses, check the picture like below.

8. EYE-Q function check

Step1) Turn on TV

Step 2) Press EYE key of Adj. R/C.

Step 3) Cover the Eye Q sensor on the front of the using your

hand and wait for 6 seconds.

Step 4) Confirm that R/G/B value is lower than 10 of the “Raw

Data(Sensor data, Back light)”. If after 6 seconds, R/

G/ B value is not lower than 10, replace Eye Q sensor

Step 5) Remove your hand from the Eye Q sensor and wait

for 6 seconds.

Step 6) Confirm that “ok” pop up. If change is not seen, replace

Eye Q sensor.

Содержание 32LN5650






































































Результаты поиска

Содержание 32LN5650

Отзывы:

Бренды по названию

Популярные бренды

LG 32LN5650, Руководство по обслуживанию

Результаты поиска

Содержание 32LN5650

Отзывы:

Бренды по названию

Популярные бренды