background image

- 10 -

LGE Internal Use Only

Copyright  © 

  LG Electronics. Inc. All rights reserved.

Only for training and service purposes

4. White Balance Adjustment

4.1. Overview

4.1.1. W/B adj. Objective & How-it-works

(1) Objective: To reduce each Panel’s W/B deviation

(2)  How-it-works:  When  R/G/B  gain  in  the  OSD  is  at  192,  it 

means the panel is at its Full Dynamic Range. In order to 

prevent saturation of Full Dynamic range and data, one of 

R/G/B is fixed at 192, and the other two is lowered to find 

the desired value. 

(3) Adj. condition: normal temperature

1) Surrounding Temperature: 25 °C ± 5 °C

2) Warm-up time: About 5 Min◦

3) Surrounding Humidity: 20% ~ 80%

4)  Before  White  balance  adjustment,  Keep  power  on 

status, don’t power off

4.1.2. Adj. condition and cautionary items

(1)  Lighting condition in surrounding area surrounding lighting 

should be lower 10 lux. 

     Try to isolate adj. area into dark surrounding.

(2)  Probe  location:  Color Analyzer(CA-210)  probe  should  be 

within 10 cm and perpendicular of the module surface

     (80°~ 100°)

(3) Aging time

1)  After Aging  Start,  Keep  the  Power  ON  status  during  5 

Minutes.

2)  In case of LCD, Back-light on should be checked using 

no signal or Full-white pattern.

4.2. Equipment

(1)  Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12 / LED: 

CH14)

(2)  Adj.  Computer  (During  auto  adj.,  RS-232C  protocol  is 

needed)

(3) Adjust Remocon

(4) Video Signal Generator MSPG-925F 720p/204-Gray

     (Model: 217, Pattern: 49) 

* Color Analyzer Matrix should be calibrated using CS-1000.

4.3. Equipment connection

4.4. Adjustment Command (Protocol)

(1) RS-232C Command used during auto-adj.

(2) Adjustment Map

4.5. Adjustment method

4.5.1. Auto WB calibration

(1)  Set TV in ADJ mode using P-Only key(or POWER ON key).

(2)  Place optical probe on the center of the display.

     -  It need to check probe condition of zero calibration before 

adjustment.

(3) Connect RS-232C Cable

(4) Select mode in ADJ Program and begin a adjustment.

(5)  When  WB  adjustment  is  completed  with  OK  message, 

check adjustment status of pre-set mode. (Cool, Medium, 

Warm)

(6) Remove probe and RS-232C cable.

▪  W/B Adj. must begin as start command “wb 00 00” , and 

finish as end command “wb 00 ff”, and Adj. offset if need.

4.5.2. LED White balance table

- If Model is Polaris Model, G-gain fix is applied.

(1) Cool Mode

1)  Purpose  : Adjust  the  color  temperature  to  reduce  the 

deviation of the module color temperature.

2)  Principle  :  To  adjust  the  white  balance  without  the 

saturation,  Fix  the  G  gain  to  172  (default  data)  and 

change the others (R/B Gain ).

3) Adjustment mode : mode - Cool

(2) Medium / Warm Mode

1)  Purpose  : Adjust  the  color  temperature  to  reduce  the 

deviation of the module color temperature.

2)  Principle  :  To  adjust  the  white  balance  without  the 

saturation,  Fix  the  one  of  R/G/B  gain  to  192  (default 

data) and decrease the others.

3) Adjustment mode : Two modes - Medium / Warm

Color Analyzer

 

Computer 

Pattern Generator

 

RS-232C 

RS-232C 

RS-232C 

Probe

Signal Source

* If TV internal pattern is used, not needed

RS-232C COMMAND

Explantion

CMD

DATA

ID

wb

00

00

Begin White Balance adjustment

wb

00

ff

End White Balance adjustment

(internal pattern disappears )

Adj. item

Command

(lower caseASCII)

Data Range

(Hex.)

Default

(Decimal)

CMD1

CMD2

MIN

MAX

Cool

R Gain

j

g

00

C0

G Gain

j

h

00

C0

B Gain

j

i

00

C0

R Cut
G Cut
B Cut

Medium

R Gain

j

a

00

C0

G Gain

j

b

00

C0

B Gain

j

c

00

C0

R Cut
G Cut
B Cut

Warm

R Gain

j

d

00

C0

G Gain

j

e

00

C0

B Gain

j

f

00

C0

R Cut
G Cut

Содержание 22LN4050


































Отзывы: