Lexmark 4227-100 Скачать руководство пользователя | Manualshive

Страница: 20 / 134

background image

1-9

4227-100

Lights

LineFeed

• Advance the paper to the next line.

FormFeed

• Advance the paper to the TOF position on

the next page.

• Load the forms to the TOF position.

Light

When you see this light

Power (Green)

The printer power is on.

Ready (Green)

The printer is online and ready to print.
The following conditions cause the Ready light
to turn off:
• Pressing Start/Stop
• An end-of-form (EOF)
• A paper jam
• A cover open
• A hardware error
• A Power-On Self Test failure.
• The printer is offline.

Check (Yellow)

Any of the following conditions may have
occurred:
• An end-of-form (EOF)
• A paper jam
• A cover open
• A hardware error
• A data transmission error
• An interface mode error
• A Power-On Self Test (POST)

failure.

Auto Gap (Green)

Auto Gap is on. Auto Gap automatically adjusts
the printer according to the thickness of the
paper you are using.

Tractor2 (Green)

The Tractor 2 Feeder is selected. (The Tractor 2
Feeder option must be installed.)

Press this button:

To:

«
...
18
19
20
21
22
...
»

Содержание 4227-100







































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4227-100

Бренд: Minolta Страницы: 168

Бренд: Triumph Adler Страницы: 4

Бренд: Triumph Adler Страницы: 263

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды