manualshive.com logo in svg

Lexington Forge SS28VFBN, Инструкция по установке и эксплуатации

Поделиться
Скачать
Lexington Forge SS28VFBN Скачать руководство пользователя страница 19

18                                                                                                                                                                                 

46D0600

46D0600                                                                                                                                                                                                    

19

��

���

�

����

�

���

�

���

���

���

��

���

��

���

����

���

�

���

OPERATING INSTRUCTIONS

   1.   STOP! Read the safety information label.
   2.   Make sure the manual shutoff valve is fully open.
   3.   This gas log set is equipped with an ignition device (piezo) which automatically lights the pilot. If piezo 

ignitor does not light the pilot, refer to instructions for “Match Lighting Instructions”, page 20.

   4.   Turn gas control knob clockwise 

 to the OFF position, set the thermostat to the lowest setting and 

turn ON/OFF switch to OFF position.

   5.   Wait (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! 

Follow the instructions under “What To Do if You Smell Gas,” page 18. If you don't smell gas, go to 
next step.

   6.   From OFF position, turn the gas control knob counterclockwise 

 to IGN position. Push in control 

knob for 5 seconds. 

NOTE: If you are running the heater for the first time, it will be neces-

sary to press in the control knob for 30 seconds or longer to allow air to bleed out of the 
gas piping. 

   7.   With the control knob pushed in, the battery powered ignition will light the pilot.
   8.   Continue pushing the control knob in for a further 10 seconds to prevent the flame detector from shutting 

off the gas while the probe is warming up. Release the control knob.

   9.   Turn gas control knob counterclockwise 

 to the ON position.

 10.   After the pilot has been lit for one minute, the burners can be turned on. Turn the ON/OFF switch to ON 

position or adjust thermostat to desired setting. 

NOTE: To use the optional thermostat function (if 

installed), the control knob must be set to “ON” and the ON/OFF Switch must be in the “OFF” 
position. 

 11.   If the gas logs will not operate, follow the instructions “To Turn Off Gas To Heater” below and call your 

service technician or gas supplier.

Figure 17 - Pilot 

 

TO TURN OFF GAS TO HEATER

 

   1.   Turn control knob clockwise 

 to OFF position to completely shut off the heater.

   2.    If applicable: Turn ON/OFF switch to OFF position and/or set thermostat (if present) to lowest setting.
   3.   If applicable: Turn off all electric power to the heater.

Figure 18 - Control Cover Plate for Milli-Volt 

Hi/Lo Control 

Ignitor/Pilot Control

 MILLI-VOLT CONTROL LIGHTING INSTRUCTIONS 

On/Off T-Stat 

Switch

Optional T-Stat 

Содержание SS28VFBN





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды