background image

1. Disconnect steering chain.

Remove control panel & pedestal head from console. Disconnect 

the steering chain by slackening the chain tensioner and removing 

the chain completely from the steering unit.

2. Mount drive to base.

Position the mounting bracket over the studs on the base plate & 

secure lightly with M8 nuts and washers.

Single wheel yachts post 2005
Ensure rudder is at Mid-Ship position  

and locked in place.

3.6 Bavaria drive installation

GB

3.6-1

M8

3.6-2

1. Mounting the drive and connecting to the steering 

system

 

!

Complete a steering check

 

!

Before you secure the drive to your boat, you must first check 

the suitability of the mounting location.

 

!

Attach the drive to a suitable mounting position with M8 bolts, 

washers and lock nuts

 

!

Use Loctite™ or similar on threads.

2. Sprocket alignment

 

!

Attach chain.

 

!

Both sprockets must be accurately aligned to run in the 

same plane when viewed from the side. Check for correct 

alignment by holding a ‘straight edge’ between the edges of 

the sprockets.

 

!

The Drive Unit can slide Fore and Aft +/- 6 mm to align the 

chain sprockets.

Adjusting the chain tension

 

!

Adjust the chain tension until it is just tight, so there is minimal 

lost motion between the drive sprocket and the rudder stock.

 

!

To adjust chain tension use the turnbuckle to take up the slack. 

Ensure the locknuts are tightened afterwards to maintain this 

position 

Note: If the chain tension is not set correctly, the resulting lost 

motion will impair steering performance. 

Over tension will diminish drive performance and reduce feel 

when manual helming.

3.5 Typical Constellation drive installation

3.5-1

3.5-2

Содержание 89300136















Отзывы: