Levitronix PuraLev 200SU Скачать руководство пользователя страница 6

Страница: 6 / 37

User Manual for PuraLev

200SU

www.levitronix.com

PL-4030-00, Rev06, DCO# 20-144

2.2 System Overview and General Specification

2.2.1 Stand-Alone System Configuration

The stand-alone pump system configuration

(Figure 3)

, consists of a controller with an integrated user panel

to set the speed manually.

The speed is automatically stored in the internal EEPROM of the controller. As an

option, the speed can also be set with an analogue signal.

Figure 3: Standard system configuration for standalone operation

(Speed setting with integrated user panel)

2.2.2 Extended System Configuration

The extended version of the pump system (

Figure 4

) consists of a controller with an extended PLC interface.

This allows setting the speed by an external signal and enables precise closed-loop flow or pressure control

in connection with either a flow or a pressure sensor. A USB interface allows communication with a PC in

connection with the

Levitronix

Service Software

. Hence parameterization, firmware updates and failure

analysis are possible.

Figure 4: Standard system configuration for extended operation

(Pressure or flow control with external sensor)

Chemical Resistance and IP67 Space

Motor

Disposable

Pump Head

Fluid In

Fluid Out

Motor Cable

Adaptor/Extension

Power Supply

24-48 VDC

200 W

Controller

for

Standalone

Operation

Stand Alone

Operation

Speed Control

PLC Interface
Speed Setting

- 1x Digital Input (Enable)
- 1x Digital Output (Status)
- 1x Analog Input (Speed)

Bayonet Socket
with Locking Pin

Chemical Resistance and IP67 Space

Motor

Disposable

Pump Head

Fluid In

Fluid Out

Motor Cable

USB
- Service
- Firmware Update
- Configuration etc.

Flow- or

Pressure

Sensor

Adaptor/Extension Cable

Extended PLC Interface
Speed, Flow
or Pressure Setting

- 4 Digital Inputs
- 4 Digital Outputs
- 4 Analoge Inputs
- 2 Analoge Outputs

Power Supply
24-48 VDC / 200 W

Controller

for

Extended

Operation

Bayonet Socket
with Locking Pin

Motor option with direct
cabling to controller

Motor option with
direct cabling
to controller

Содержание PuraLev 200SU






































Результаты поиска

Содержание PuraLev 200SU

Отзывы:

Бренды по названию

Популярные бренды

Levitronix PuraLev 200SU, Руководство пользователя

Результаты поиска

Содержание PuraLev 200SU

Отзывы:

Бренды по названию

Популярные бренды