Levitronix PLD-iF30SU.1 Скачать руководство пользователя страница 24

Страница: 24 / 39

User Manual for PuraLev

iF30SU

www.levitronix.com

PL-4078-00, Rev00, DCO# 20-228

4.2.7 Installation of RS485 Fieldbus Flow Control System Arrays

Figure 23

shows a typical multi-system arrangement with the

RS485

fieldbus and its basic specifications for

the

EasyConnect

Model.

Figure 23: Multi-system arrangement with EasyConnect models with RS485 fieldbus

(See Table 4 for cable specifications.)

Following points and information shall be considered:

➔

Various standard cables (see

Table 4

) are available to simplify the installation of a fieldbus array

as illustrated in

Figure 23

➔

Testing has been done with arrangements of 8 drive systems. Higher number is possible, but it is
recommended to contact

Levitronix

Technical Service

department (see

Section 8

) for details and

support.

➔

Address setting of the pump units can be done with the

Levitronix

Service Software

and a

PC.

A USB/RS485 converter cable with integrated initialization network can be ordered according to

Table 4

➔

The fieldbus array must be terminated as illustrated in

Figure 23

. A dedicated connector with

integrated termination resistor (see

Table 4

) is available.

➔

The

RS485 Modbus RTU

protocol for master communication is available at

Levitronix

request.

➔

Do not use multiple master systems at the same time and do not use closed ring arrangements.

4.2.8 Installation of Fieldbus for Blending

Blending setup with 2 pumps can be done as shown in

Figure 6

Same instructions can be followed as

mentioned in

Section 4.2.7

Integrated Flow Control

Driver

EasyConnect Model

Power

Supply

PLC

Fieldbus

OUT

Fieldbus

IPS Cable Signal

Integrated Flow Control

Driver

EasyConnect Model

Power

Supply

PLC

Fieldbus

OUT

Fieldbus

Integrated Flow Control

Driver

EasyConnect Model

Power

Supply

PLC

Fieldbus

OUT

Fieldbus

IPS Cable Signal

24 VDC

Supply

24 VDC
Supply

Master

Fieldbus
Termination
Connector

120



510



510



Initialization Network:

Always recommended.

To be implemented at the master.

RS485+

RS485-

Single-Use

Pump Head

Single-Use

Pump Head

Single-Use

Pump Head

Flow
Sensor

10a

10b

Содержание PLD-iF30SU.1








































Результаты поиска

Содержание PLD-iF30SU.1

Отзывы:

Бренды по названию

Популярные бренды

Levitronix PLD-iF30SU.1, Руководство пользователя

Результаты поиска

Содержание PLD-iF30SU.1

Отзывы:

Бренды по названию

Популярные бренды