Leviton GreenMax DRC DRC07-ED0, Быстрый старт

Страница: 1 / 2

The DRC Controller and Smart Pack combines all the functionality of a DRC Controller and Load
controlling Smart Pack in a single device. As with any DRC Controller, this device is responsible
for management of all the architectural controls and energy management business logic within a
VLQJOHURRPDQGLVIXOO\VHWXSDQGFRQ¿JXUHGXVLQJD:L)L
® enabled cell phone or tablet.
• The LumaCAN™ network can span multiple rooms and connect multiple DRC devices
together; however it is important to pay particular attention to setup and control of rooms to
avoid cross room control.
• Each DRC Controller can connect to a variety of devices, such as DRC smart packs, relay
SDQHOVDQGLQWKHIXWXUH,QWHOOHFWŒ¿[WXUHV/XPLQDŒ5)VHQVRUV'$/,ŒGHYLFHVDQGRWKHU
GHYLFHV)RUVSHFL¿FFDSDELOLWLHVDQGFDSDFLWLHVUHIHUWRWKHSURGXFWGDWDVKHHW
3.
Connect LumaCAN (See port locations in Operation step 1)
7ZR/XPD&$1SRUWVDUHSURYLGHGWRPDLQWDLQWKHUHTXLUHG'DLV\&KDLQWRSRORJ\RIWKH
LumaCAN network. Plug in CAT6 cable with standard RJ45 connector. If two connections are
required, remove the terminator from one of the RJ45’s and make both connections. If only
one connection is required, leave the supplied terminator connected.
‡:LUHSHUWKH7,$%VWDQGDUG
• The sequence of network nodes, as described in the construction documents, may be critical
to ensure power distribution between nodes.
‡$OO/XPD&$1FDEOHVHJPHQWVPXVWEHQHWZRUNFDEOHWHVWHGDQGYDOLGDWHGSULRUWRSRZHUXS
of the system.
• The last device in each LumaCAN run must be terminated using an RJ45 terminator plug.
(DFK6PDUW3DFNLVVXSSOLHGZLWKRQHWHUPLQDWRUSOXJSUHLQVWDOOHGLQWKH6PDUW3DFN
Additional terminators are available upon request. LumaCAN connections must be wired as
Class 2 and as such should be installed according to the requirements of your authorities
having jurisdiction. If it is required that the Class 2 wiring be in conduit, use a 4 in. square
H[WHQVLRQULQJDQGEODQNSODWHRQWKH/XPD&$1VLGHRIWKH6PDUW3DFNDQGWHUPLQDWH
FRQGXLWWRWKHH[WHQVLRQULQJ
‡2QFHFRPSOHWHUHVWRUHSRZHUWRWKHFLUFXLWEUHDNHURUIXVH:KHQSRZHULVDSSOLHG'5&
Smart Pack will power up in the ON state and then default to the last powered down state.
The default from the factory is ON after power up.
WARNINGS
• READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TURN
OFF POWER AT THE 24 HOUR NIGHT LIGHT/EMERGENCY CIRCUIT AND TEST THAT POWER IN BOTH
CIRCUITS IS OFF BEFORE WIRING, SERVICING, OR REMOVING FIXTURE. THIS FIXTURE IS POWERED
BY TWO (2) CIRCUITS: THE REGULAR POWER BRANCH CIRCUIT AND THE 24 HOUR NIGHT LIGHT/
EMERGENCY CIRCUIT.
• "EMERGENCY CIRCUITS" enclosed label should be placed in a highly visible location if any DRC Smart Pack
LVSDUWRIWKHHPHUJHQF\V\VWHPVRDVWREHUHDGLO\LGHQWL¿DEOHDVDFRPSRQHQWRIWKHHPHUJHQF\V\VWHP
• Do not mount near gas or electric heaters.
• The use of accessory equipment is not recommended by the manufacturer may cause an unsafe condition.
‡7RDYRLGHOHFWULFDORYHUORDGWRWDOFRQQHFWHGODPSORDGVKDOOQRWH[FHHGRXWSXWUDWLQJ
WARNINGS
‡7HVWDOO/XPD&$1FDEOHVIRUFRPSOLDQFHWR7,$%SULRUWRLQWHUFRQQHFWLQJGHYLFHVDQGV\VWHPV
• Equipment should be mounted in locations and at heights where it will not be subjected to tampering by
unauthorized personnel.
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
CAUTIONS
• Do not use this equipment for other than intended use.
‡)RULQGRRUDSSOLFDWLRQVRQO\
SAVE THESE INSTRUCTIONS
WARNING : TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker
or fuse and test that power is off before wiring!
NOTE:
This is an ESD Sensitive Device. Use safe ESD handling procedures
when installing.
1.
Mount.
Product Description
Installation
DRC™ Controller and Smart Pack
&DW1RV'5&(''5&(
INSTALLATION AND QUICK START SHEET
ENGLISH
','5&$
a.
0RXQWWRIDFHRILQVTMXQFWLRQER[ZLWKPLQLPXP
YROXPHFXLQRUJUHDWHULQ[LQ[LQ
using the provided screws.
NOTE the following:
• Ensure that conduit/cable entry clamp is located in
DFRUQHURIMXQFWLRQER[RSSRVLWHWKH'5&QLSSOHDV
FRQÀLFWVPD\RFFXU
• Dress wires to provide enough clearance when
device is installed.
b.
Preferred installation method is 1a above, but the product may also be mounted using
WKHQLSSOHWKURXJKDMXQFWLRQER[NQRFNRXW
NOTE : ensure all indicators remain visible
DQGDFFHVVLEOHSRVWLQVWDOODWLRQ
2.
:LUH
:LUH/LQHYROWDJHDQGFRQWUROZLULQJSHUZLULQJGLDJUDP,IFRQWURO9ZLULQJLVWREHUXQ
as class 2, sleeve wires with suitable insulating material from the Smart Pack throughout until
WKH\H[LWWKHMXQFWLRQER[
Hot
0-10V (violet)
Com (gray)
Neutral
(white)
LumaCAN
Hot (blue)
Neutral
BLK
WH
WH/BL
BL/WH
Normal
Lighting
Smart
Pack
Normal
Panel
To Normal
Lighting Load
LumaCAN
Green
SPECIFICATIONS
Cat. No.
'5&(' '5&(
Input Voltage/Frequency
9$&+]
347VAC, 60Hz
Input Power
0D[
:#9
:#9
12W @ 347V
Standby
:#9
:#9
2.3W @ 347V
Load Ratings
20A Tungsten
20A General Purpose Plug Load
20A Standard Ballast
16A Electronic Ballast, LED
12A Electronic Ballast, LED
Motor Ratings
1/2Hp (9.8 FLA) @ 120VAC
2 Hp (12 FLA) @ 240-277VAC
N/A
0-10V Control 0.8 - 10+VDC, 100mA Sinking
LumaCAN Data
/XPD&$12QO\
'DLV\&KDLQ7RSRORJ\
IHHWPD[SHUVHJPHQW
5HSHDWHUVFDQEHXVHGIRUQHWZRUNVXSWRIHHWDQGWRVXSSRUWKRPHUXQWRSRORJ\
0D[QRGHVSHUVHJPHQW
0D[QRGHV
Termination required at end of line, termination jumper provided
LumaCAN Power
P$3RZHU6XSSO\SURYLGHGWR/XPD&$1ZKHQ(06HQVHVZLWFKLVLQ/,1(SRVLWLRQ
:KHQ(06ZLWFKLVLQ&$1SRVLWLRQQRSRZHUVXSSOLHGWR/XPD&$1QHWZRUN
1RGLRGHVRQ5-¶VSRZHUDOZD\VSDVVHVWKURXJK
Connections
$:*3RZHU9
$:*/RDG,1287
RJ45, CAT6A or better (LumaCAN)
LED Indicator Yes
Dimensions
[[
Weight 0.6 lb (9 oz)
Mounting
6WDQGDUG´VTXDUHMXQFWLRQER[ZLWKPLQLPXPYROXPHRIFXLQFKHVRUJUHDWHU
[[XVLQJWKHWZRSURYLGHG[VFUHZV2UPRXQWHGWRMXQFWLRQ
ER[YLDQLSSOH
LumaCAN Connections CAT6 cable
Operational Temperature
ƒWR)ƒƒWRƒ&
IP Rating
,3
GreenMax
®
Heartbeat Indicator
Indicator Feature
Light
Status
Possible Causes/Resolution
Red
Failed application or
processor failure
solid
Cycle power. If a power cycle does not restore proper operation, remove
LumaCAN cables and cycle power again. Do not reconnect LumaCAN
until after normal operation is restored.
Duplicate LumaCAN address blinking
Log into controller with app and change LumaCAN address to a unique
address.
White
Processor in reset or startup
failure
solid
Cycle power. If a power cycle does not restore proper operation, remove
LumaCAN cables and cycle power again. Do not reconnect LumaCAN
until after normal operation is restored.
Off Failure off
Remove LumaCAN cables. If device starts up, then there is either an
overcurrent or short on the LumaCAN cables. Resolve the problem and
reconnect. If removing cables does not solve the problem, check control
Power Input.
6
LuminaRF/Intellect/Zigbee Switch Actions
Action Feature Result
Press/Release <1 second Status indication
2QHEOLQNQRWFRQ¿JXUHG7KUHHEOLQNVQHWZRUN
formed
10 second press Enable/disable
UDSLGÀDVKHVZKHQWULJJHUHG
20 second press Reset device to factory default state
5DSLGFRQWLQXRXVÀDVKLQJUHVHWWULJJHUHGRQUHOHDVH
>25 second press LED goes dark
:KHQUHOHDVHGQRDFWLRQZLOOEHWDNHQ
2
Wi-Fi Indicator
Indicator Feature
Solid GREEN
:L)LHQDEOHGQRWUDI¿F
%OLQN*5((1 1HWZRUNWUDI¿F
2)) :L)LGLVDEOHG
LumaCAN Indicator
Indicator Feature
Solid GREEN LumaCAN enabled
%OLQN*5((1 7UDI¿F
2))
LumaCAN disabled
LuminaRF/Intellect/Zigbee Indicator
Indicator Feature
Solid GREEN
(QDEOHGQRWUDI¿F
%OLQN*5((1 1HWZRUNWUDI¿F
2))
Disabled
5 4 3
Indicator lights and switches (for normal operation)
Wi-Fi Switch Actions
Action Feature Result
Press/Release <1 second
(also can be done with power cycle)
5HWULJJHU66,'EURDGFDVW
SSID broadcast times out after 15 minutes
10 second press
(QDEOHGLVDEOH:L)L UDSLGÀDVKHVZKHQWULJJHUHG
20 second press
5HVHW:L)LQHWZRUNFRQ¿JXUDWLRQ
to factory default state
5DSLGFRQWLQXRXVÀDVKLQJUHVHWWULJJHUHGRQUHOHDVH
>25 second press LED goes dark
:KHQUHOHDVHGQRDFWLRQZLOOEHWDNHQ
1
1 2 3 4 5 6
•
:KHQLQVWDOOLQJLQMXULVGLFWLRQVZKLFKUHTXLUH&ODVVQHWZRUNZLULQJLQFRQGXLWDGGD
LQVTXDUHH[WHQVLRQULQJRQWRSRIWKHVPDUWSDFNDQGDEODQNFRYHURQWRSRIWKDW
7KHVPDUWSDFNZLOOWKHQEHVDQGZLFKHGEHWZHHQWZRMXQFWLRQER[HVVRRQHFDQEH
used for Class 2 and the other for Class 1.
• Some jurisdictions, like Chicago, may require the smart pack to be installed into a
PHWDOHQFORVXUH:KHQWKLVLVUHTXLUHGWKHFRQWUDFWRUVKDOOSURYLGHDSSURSULDWH
enclosure or request the appropriate enclosure from Leviton.
Mounting Screws
WEB
VERSION