PK-A3267-10-00-5A
AR3128
© 2018 Leviton Mfg. Co., Inc.
Configuration
1.
Configure IP settings.
All configuration is done through the HTML configuration interface. To enter the
configuration interface from your web browser, navigate to a web page using the following
IP address and the default username/password credentials.
• Default IP address: 192.168.0.11
• Default web link: http://192.168.0.11
• Default user: admin
• Default password: admin
Replace the IP address in the web link at LEFT with whatever IP address you configure below. In order to connect
directly from your PC you will need to ensure your PC and the device are on the same subnet.
NOTE
: Configuration steps may be performed in any order; however, the process below is recommended.
2.
Update Firmware.
• Current firmware release can be found on Leviton’s field service FTP site.
Contact Tech Support for details if needed.
• Update firmware on the maintenance menu. Select the firmware and proceed
through the update process.
• Update IP address setting from the INTERFACE MENU.
• Only fixed IP addresses are supported at this time.
• In this application the total draw from LumaCAN is 60mA for the gateway.
•
IP communication is only required for setup and configuration, it is not required for
day to day operation.
3.
Configure your DALI Networks.
• Select the channel you want to configure (Channel 1 or Channel 2).
• Choose MAKE NEW INSTALLATION or READ CURRENT INSTALLATION. This
initiates the process of creating and forming a DALI network and assigning short
addresses to all of the devices. Any device that currently has a short address may
be reset. MAKE NEW INSTALLATION should be selected only the first time a
network is created. All future network changes/updates should be done by selecting
READ CURRENT INSTALLATION.
NOTE
: When selecting READ CURRENT INSTALLATION, short addresses are not
changed and all existing programmed parameters remain. This option should be selected
on all networks after first configuration.
• Each of the properties below can be set for each device on the network. Parameters
are set by entering data into the fields.
• LumaCAN Channel Numbers - each channel number must be unique for each
device on the network.
• Brightness Level - indicates the current dimmed level of this device. Can be used to
temporarily set a test level for the device and validate communication.
• Fade Time/Rate - fixed fade time for this device. LumaCAN fade times are ignored
and the fixed fade time is used for all commands. This is so that DALI network is not
overly congested.
• Minimum/Maximum Level - the minimum/maximum control level. Default = 1/100%.
• Groups - not used at this time.
• Scenes - not used at this time.
• System
Status
1. Green - Device is online and communicating.
2. Red - Device is offline.
• Find - used to trigger device identify. Each device determines its own identify
response, but typically light fixtures will turn on and off and sensors/switches will
blink their LED indicator lights
4.
Configure Installation.
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase
date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option.
For details visit www.leviton.com or call 1-800-824-3005.
This warranty excludes and there is disclaimed liability for labor for removal of
this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in
accordance with any labels or instructions.
There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose
, but if any implied warranty is required by the applicable jurisdiction, the
duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years.
Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation,
damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation
. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of
Canada Ltd to the attention of the Quality Assurance Department,
165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
FCC AND INDUSTRY CANADA COMPLIANCE STATEMENT
:
FCC & IC Statement - This device complies with Part 15 of the FCC Rules and ISED License-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by
Leviton could void the user’s authority to operate the equipment.
These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This Class A digital apparatus complies with Canadian CAN ICES-3(A)/NMB-3(A).
TRADEMARK DISCLAIMER:
The Leviton word mark and logo and the LumaCAN trademarks, are the property of Leviton
Manufacturing Inc., Co. DALI is a third-party trademarks the property of its owners. Use herein of third party trademarks, service
marks, trade names, brand names and/or product names are for informational purposes only, such use is not meant to imply affiliation,
sponsorship, or endorsement.
Specifications
Power Input: Gateway
VDC 24V ±20% 60mA (Provided through LumaCAN
or Power Input Terminal)
Power Input: DALI
23 - 30V VDC
250mA - Single DALI Channel in use
500mA - Two DALI Channels in use
Physical Interfaces
1x CAN, 2x DALI, 1x Ethernet
Communication Protocols
LumaCAN, DALI
DALI Load Capability
max 250mA per channel
DALI Devices
64 per channel
Max Cable Length (DALI)
300m (984 ft)
Ethernet
1x 10/100 Base T on RJ-45 Connection
Operating Temperature Range
0°C - 45°C (32°F - 113°F)
Storage and Transportation Temperature
-10°C - 70°C (14°F - 158°F)
Maximum Air Humidity
0-90%, non-condensing
Dimensions (W x H x D)
70 x 86 x 59mm (2.76 x 3.39 x 2.32 in)
Protection Level
IP20
FCC SUPPLIER’S DECLARATION OF CONFORMITY:
Model DRCDD – 0L0 is Manufactured by Leviton Manufacturing Inc. 201 N Service Rd, Melville, NY 11747.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
WEB
VERSION
