Hot (Black)
Neutral (White)
Load
Mural
Dimmer
Blue
Yellow
Green
Ground
Black
White
Black
Line
120VAC, 60Hz
Cap with
Wire Connector
(OR PRIMARY SIDE OF
MAGNETIC LOW-VOLTAGE
TRANSFORMER)
}
Wiring Diagram 1 – Single Control Application
Hot (Black)
Neutral (White)
Load
Mural
Dimmer
Blue
Blue
Yellow
Yellow
Green
Ground
Green
Ground
Black
White
Black
Line
120VAC, 60Hz
Multi-Remote
MSØØR-1
(OR PRIMARY SIDE OF
MAGNETIC LOW-VOLTAGE
TRANSFORMER)
}
Wiring Diagram 2 – Two Location Control Application
Hot (Black)
Neutral (White)
Load
Mural
Dimmer
Blue
Blue
Blue
Yellow
Yellow
Yellow
Green
Ground
Green
Ground
Green
Ground
Black
White
Black
Line
120VAC, 60Hz
(OR PRIMARY SIDE OF
MAGNETIC LOW-VOLTAGE
TRANSFORMER)
}
Multi-Remote
MSØØR-1
Multi-Remote
MSØØR-1
Wiring Diagram 3 – Three Location Control Application
7.
The brightness adjustment is located on the side of the dimmer
(refer to Figure 1)
. Using a small, insulated
screwdriver, depress the brightness adjustment switch. To increase the minimum brightness, press the upper
half of the rocker. To decrease the minimum brightness, press the lower half of the rocker.
8.
Release the rocker. Release adjustment switch and minimum brightness is set. Check for proper operation
by tapping the lower half of the rocker so the lights turn OFF, then tapping the upper half of the rocker so the
lights turn ON. The lights will turn ON to the new minimum brightness set. If operation is not satisfactory,
repeat step 7.
9.
Attach Decora
®
wallplate (not included).
INSTALLATION IS COMPLETE.
NOTE:
On the lower left corner of the switch plate, there is an air-gap switch. When servicing a controlled
fixture, pull lever out (OFF position). This will cut the power to the fixture. After servicing is complete, push the
lever in (ON position) to restore power. The lever must be pushed in all the way (ON position) for normal
operation.
COLOR CONVERSION PROCEDURE
The color of this device can be changed to suit your interior design requirements. Simply obtain a color
conversion kit of the appropriate color from your Leviton distributor and proceed as follows (please note that
wallplate must be removed).
1.
Select the color of the face you desire.
2.
The frame has snaps on its sides. Using a small screwdriver,
gently
remove the frame from the strap
(refer
to Figure 2)
.
3.
Take the new frame and position it properly to the strap. Notice that the frame has a cut-out for the air-gap
switch lever. Line up the plastic snaps with the square holes in the strap. Insert the snaps on one side of the
frame into the strap.
4.
Firmly press sideways and down to slip the other snaps into place. The frame snaps in with a audible click.
Ensure that all four snaps are secure. Replace Decora
®
wallplate.
The color conversion is complete.
TO OPERATE:
ON:
Tap the upper half of the rocker. The lights will brighten to the last set light level.
OFF:
Tap the lower half of the rocker. The lights will dim to OFF.
BRIGHTEN:
Press and hold the upper half of the rocker to the desired light level.
FULL BRIGHT:
If the lights are OFF, double tap the upper half of the rocker. The lights will turn ON FULL
BRIGHT.
If the lights are ON, tap the upper half of the rocker once. The lights will turn ON FULL
BRIGHT.
The previous light level will remain in memory upon next ON operation
(see above)
.
FAST OFF:
Double tap the bottom half of the rocker. The lights will immediately turn OFF.
DIM:
Press and hold the lower half of the rocker to the desired level.
BRIGHTNESS LEVEL DISPLAY:
Indicates the level of brightness when the lights are ON. Indicates the previous level of brightness when the lights are
OFF
(refer to Figure 1)
.
NOTE:
To alert you that there is power to the dimmer when the load is OFF, the ON/OFF LED remains ON. To
alert you that the load is ON, the ON/OFF LED remains OFF.
NOTE:
If lights are OFF, regardless if you tap or press and hold the upper half of the rocker, the lights will go to
last set light level.
NOTE:
If a power interruption should occur while the device is ON, the light load will return to its previous light level
when power is restored within 10 seconds.
TROUBLESHOOTING
•
Light does not turn ON and ON/OFF LED does not turn ON
- Circuit breaker or fuse has tripped.
- Lamp is burned out.
- Lamp is not connected to line Neutral.
- Air gap switch is open.
•
Dimmer does not operate
- Dimmer BLACK wire miswired to lamp and Dimmer BLUE wire miswired to LINE Hot.
•
Light turns ON and Dimmer works, but Multi-Remote
TM
does not work
- There are no connections from Multi-Remote
TM
to Dimmer.
- Multi-Remote
TM
miswired to Dimmer.
•
Lights Flickering
- Lamp has a bad connection.
- Lamp power is less than 40W or 40VA.
Frame
Strap
Air-Gap
Switch
Snaps
Push in 2 Locations
ON/OFF
LED
Brightness Level Display
(Cat. Nos. MDIØ6-1, MDI1Ø-1, MDMØ6-1 & MDM1Ø-1 ONLY)
Figure 2 – Color Conversion
PK-93079-10-00-0A
PK-93079-10-00-0A
10/16/02, 4:45 PM
2
