Leviton 4000-R series Скачать руководство пользователя страница 1

Страница: 1 / 24

Installation Guide

Power Monitoring

ZL0139-0A

Page 1 of 24

05145

For use in a Pollution Degree 2 or better environment only. A Pollution Degree 2 environment

must control conductive pollution and the possibility of condensation or high humidity.

Consider the enclosure, the correct use of ventilation, thermal properties of the equipment,

and the relationship with the environment. Installation category: CAT II or CAT III. Provide

a disconnect device to disconnect the meter from the supply source. Place this device in

close proximity to the equipment and within easy reach of the operator, and mark it as the

disconnecting device. The disconnecting device shall meet the relevant requirements of IEC

60947-1 and IEC 60947-3 and shall be suitable for the application. In the US and Canada,

disconnecting fuse holders can be used. Provide overcurrent protection and disconecting

device for supply conductors with approved current limiting devices suitable for protecting

the wiring. If the equipment is used in a manner not specified by the manufacturer, the

protection provided by the device may be impaired.

CAUTION

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classified locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable fire and electrical enclosure.

FCC PART 15 INFORMATION

NOTE: This equipment has been tested by the manufacturer and found to

comply with the limits for a class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

residential environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

Modifications to this product without the express authorization of the

manufacturer nullify this statement.

WARNING

LOSS OF CONTROL

∙  Assure that the system will reach a safe state during and after a control path failure.
∙  Separate or redundant control paths must be provided for critical control functions.
∙  Test the effect of transmission delays or failures of communication links.

∙ Each implementation of equipment using communication links must be individually

and thoroughly tested for proper operation before placing it in service.

Failure to follow these instructions may cause injury, death or equipment damage.

For additional information about anticipated transmission delays or failures of the link, refer to

NEMA ICS 1.1 (latest edition).

Safety Guidelins for the Application, Installation, and Maintenance

of Solid-State Control

or its equivalent in your specific country, language, and/or location.

Control system design must consider the potential failure modes of control paths and, for

certain critical control functions, provide a means to acheive a safe state during and after a

path failure. Examples of critical control functions are emergency stop and over-travel stop.

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

•  Turn oﬀ all power supplying equipment before working on or inside the equipment.
•  Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.
•  This equipment must only be installed and serviced by qualiﬁed electrical personnel.
•  Read, understand and follow the instructions before installing this product.
•  Product may use multiple voltage/power sources. Be sure all sources of power

have been disconnected before servicing.

• Use a properly rated voltage sensing device to conﬁrm power is oﬀ.

DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

• Only install this product on insulated conductors.

Failure to follow these instructions will result in death or serious injury.

A qualified person is one who has skills and knowledge related to the construction and

operation of this electrical equipment and the installation, and has received safety

training to recognize and avoid the hazards involved.

NEC2011 Article 100

No responsibility is assumed by Leviton for any consequences arising out of the use of

this material.

DANGER

Product Overview

The Series 4000-R DIN rail meter provides a solution for measuring energy data with a single device. Inputs include
control power, CT, and 3-phase voltage. The Series 4000-R supports multiple output options, including solid state
relay contacts, Modbus, and pulse. The LCD screen on the faceplate allows instant output viewing. Series 4000-R
meters include built-in CT integrators and CT power supplies. They work only with U018 Series rope style CTs.

The meter is housed in a plastic enclosure suitable for installation on T35 DIN rail according to EN50022. The Series
4000-R can be mounted with any orientation over the entire ambient temperature range, either on a DIN rail or in a
panel. The meter is not sensitive to CT orientation to reduce installation errors.

Series 4000-R

Compact Modbus Power and Energy Meter

For Use Only With U018 Series Rope CTs

Specifications

MEASUREMENT ACCURACY

Real Power and Energy

IEC 62053-22 Class 0.5S, ANSI C12.20 0.5%

Reactive Power and Energy

IEC 62053-23 Class 2, 2%

Current

0.4% (+0.015% per °C deviation from 25°C) from 5% to 100% of

range; 0.8% (+0.015% per °C deviation from 25°C) from 1% to 5% of