www.levante-products.com
LEV0411/Page 3 of 4/Issue 1/08.16
INSTALLATION
fig. 1
fig. 2
fig. 3
Wall Plug & Screw x4
• Remove the mounting bracket from the heater by pressing inwards on the two clips then pulling the bracket down and
away from the heater (fig. 1).
• Fix the mounting bracket to the wall via the four fixing holes using wall plugs and screws (fig. 2).
• Re-attach the heater onto the mounting bracket. Hook the bottom holes onto the mounting bracket, then push the heater
so the slots lock onto the bracket clips (fig. 3). When satisfied with the installation plug in the heater to the mains power
socket and switch on to test and operate as described in the next section.
Mounting Bracket
Clip
Carefully select a suitable mounting position on a wall, near to a mains 13 Amp power outlet/socket, allowing sufficient free
space around the heater as per fig. 4.
Note: The heater is supplied with 1.2 metres of cable, but requires a 13A 3 pin plug connecting to it. Alternatively, it may be
wired directly into the nearest fused spur unit.
1
2
4 2
3 2
2 2
1 2
0
19
1
8
17
1
6
1
5
1
4
1
3
1
2
1
1
10
9 8 7 6
5
4
3
2
...
...
...
....
...
...
...
...
...
...
...
...
..
..
..
..
..
..
..
..
..
..
..
..
. .
. . .
. . .
. . . . .
. . . . . . . . . . . ..
. . ..
. ..
...
...
...
..
.
.
.
.
.
.
.
.
.
.
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .
. .
. .
. .
. .
. . .
. . . . .
. . . . . . . . .
. . .
. .
. .
. .
. .
. .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
2
4 2
3 2
2 2
1 2
0
19
1
8
17
1
6
1
5
1
4
1
3
1
2
1
1
10
9 8 7 6
5
4
3
2
...
...
...
....
...
...
...
...
...
...
...
...
..
..
..
..
..
..
..
..
..
..
..
..
. .
. . .
. . .
. . . . .
. . . . . . . . . . . ..
. . ..
. ..
...
...
...
..
.
.
.
.
.
.
.
.
.
.
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .
. .
. .
. .
. .
. . .
. . . . .
. . . . . . . . .
. . .
. .
. .
. .
. .
. .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
2
4 2
3 2
2 2
1 2
0
19
1
8
17
1
6
1
5
1
4
1
3
1
2
1
1
10
9 8 7 6
5
4
3
2
...
...
...
....
...
...
...
...
...
...
...
...
..
..
..
..
..
..
..
..
..
..
..
..
. .
. . .
. . .
. . . . .
. . . . . . . . . . . ..
. . ..
. ..
...
...
...
..
.
.
.
.
.
.
.
.
.
.
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .
. .
. .
. .
. .
. . .
. . . . .
. . . . . . . . .
. . .
. .
. .
. .
. .
. .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
OFF
ON
Constant
Timer
Controlled
20 minute Time Segments
(Outwards = ON, Inwards = OFF)
Heater Power
Thermostat
Timer Control
Max.
Temp.
Min.
Temp.
Temperature
Indicator
Mark
OFF
ON
HEATER OPERATION
1
2
min.
450mm
min.
250mm
min.
250mm
min.
150mm
fig. 4
The convector heater can be adjusted to maintain a constant
room temperature by using the thermostat. Rotate the control
clockwise to turn on and increase the room temperature.
Use along with the timer control selected to ‘ON’ or ‘timer
controlled’. When the room has reached the required
temperature the light on the front of the heater will turn off.
Please note that if the indicator light is not lit when the
heater is switched on:
a. Turn the thermostat control clockwise to a higher setting.
b. Ensure that the override switch on the timer is set to the
‘ON’ position.
Frost Protection: Turn the thermostat to the ‘MIN’ setting for
the heater to maintain a temperature above freezing.
Using the Timer Control
Turn the clock dial clockwise until the correct time aligns
with the pointer. Raise the time segments for the required
ON/OFF times and set the control switch to ‘timer controlled’.
Thermostat Control
