background image

 

 

 

Quick Start Guide HS 6508 

 

 

Page 18 

More Information to Parameterization you will find in:

 

User’s Guide HS 6508 

Parameter for Codetypes activation, number of digit .... 

Troubleshooting 

For problem detection and troubleshooting, check your scanner as follows: 

1.  When the scanner is powered through the interface cable. To do this, scanners and computer be 

connected before using the scanner with each other, must come up with the computer with a power 

supply of 5 volts DC for the scanner. Check the manual for your computer, that the power supply to hook 

up your scanner is sufficient. 

2.  Make sure that the interface cable is securely attached to the computer. In the manual of the computer for 

information on proper port on the scanner. Support is also available from your technical staff.. 

3.  If your system operates with an external power supply, make sure that the power adapter is securely 

connected to the scanner and power supply. 

4.  Verify that the interface cable is securely attached to the handle of the scanner. To do this, loosen the 

screws (at HS 6508) to the end cap of the handle with an appropriate tool. Remove the wire tie and pull 

out the cable. Run the cable back on again and make sure that it is properly seated in the cradle. Insert 

the wire tie back and fix everything with screws. 

5.  If the scanner does not, despite all the measures taken to be ready, replace the power supply with 

another recommended power supply device from which you know for sure that it is fully functional. 

6.  Make sure that the interface of your scanner is compatible with the computer. See the manual for your 

computer. Also check that the scanner is configured for the desired application. This information is 

described in the 

User’s Guide of the HS 6508. 

7.  Verify that the bar code labels that you want to scan are of satisfactory quality and that the used bar code 

symbology is recognized by your scanner. Sample label for review, contact your dealer, you need 

accurate information to the label details. (Wrinkled, torn or soiled) Damaged bar code labels can cause 

the scanner only poorly or not the label recognizes. If you suspect the problem is the quality of the label, 

check the reading readiness in terms of quality with a good label. 

8.  If the problems are not now be resolved, please contact Leuze electronic. 

Содержание HS 6508





















Отзывы: