Leuze electronic KRTL 3B Скачать руководство пользователя

Страница: 7 / 8

Leuze electronic GmbH + Co. KG

In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0

KRTL 3B… - 06

[email protected] • www.leuze.com

Pulse stretching option

Switching pulse stretching on or off:

"EasyTune" option - fine tuning of the switching threshold

Following power-on and completed teach event:

Green LED illuminates continuously (ready)
Yellow LED on/off continuously (mark detected/not detected)

Increasing the switching threshold:

Reducing the switching threshold:

If the upper or lower end of the adjustment range is reached, the green and yellow LEDs flash at a considerably higher fre-
quency of 8Hz for the duration of one second.

Press the teach button
longer than 12s.

Only the green LED flashes.

Release teach button.

After releasing the button,
the yellow LED displays the state:
yellow LED on:pulse stretching ON
yellow LED off:pulse stretching OFF

Change is accepted.

Long press of the button =
large force expenditure =
increase switching
threshold

Each press of the button with
a duration between 200ms
and 2s increments the
switching threshold.

A press of the button is acknowledged by a
single, brief

flash of the green LED

– the

new switching threshold is now valid.

Short press of the button =
small force expenditure =
reduce switching threshold

Each press of the button with
a duration between 2ms and
200ms decrements the swit-
ching threshold.

A press of the button is acknowledged by a
single, brief

flash of the green LED

– the

new switching threshold is now valid.

> 12s

The pulse stretching is switched

off

The pulse stretching is switched

Label with marks

Receive signal

1. Teach point on background

2. Teach point on mark

2-point teach

1-point teach

Switching threshold

Increase the swit-

ching threshold

Label with marks

Receive signal

Teach reference value

Switching threshold

Increase the swit-

ching threshold

200ms … 2s

Green

LED flashes

briefly once

Label with marks

Receive signal

1. Teach point on background

2. Teach point on mark

2-point teach

1-point teach

Switching threshold

Reduce the swit-

ching threshold

Label with marks

Receive signal

Teach reference value

Switching threshold

Reduce the swit-

ching threshold

2ms … 200ms

Green

LED flashes

briefly once

KRTL 3B

Laser contrast scanner

Содержание KRTL 3B









Результаты поиска

Содержание KRTL 3B

Отзывы:

Похожие инструкции для KRTL 3B

Бренды по названию

Популярные бренды

Leuze electronic KRTL 3B, Руководство пользователя

Результаты поиска

Содержание KRTL 3B

Отзывы:

Похожие инструкции для KRTL 3B

Бренды по названию

Популярные бренды