Leuze electronic 50038948 Скачать руководство пользователя страница 30

Страница: 30 / 74

Accessories/order codes

BCL 8

Leuze electronic

5.3.2

MA 8

01 - SW IN/OUT - switching input and switching output

Figure 5.1: MA 8-01 - Pin assignment SW IN/OUT

SW IN/OUT (5-pin socket, A-coded)

Name

Comment

VOUT Voltage supply for sensor system (VOUT

identical to VIN at PWR IN)

SWOUT Switching output

GND

GND for the sensor system

SWIN Switching input

Functional earth

Thread

Functional earth (housing)

SWIN

VOUT

GND

SWOUT

SW IN/OUT

M12 socket

ATTENTION!

Degree of protection IP 67 is achieved only if the connectors and caps are screwed into

place!

NOTE

The switching input/switching output are programmed via the parameters in the BCLconfig

configuration software. For more information see also Chapter 10.6 and Chapter 10.8,

Page 54 et seq.

ATTENTION!

If you use a sensor with a standard M12 connector, then please note the following:



Use only sensors on which the switching output does not lie on pin 2 or sensor cables

on which pin 2 is not assigned. Otherwise, the switching output is not protected against

feedback on the switching input. If the inverted sensor output lies on pin 2, erroneous

behavior of the switching output will result.

UM_BCL8_de_50040581.book Seite 28 Montag, 24. Februar 2020 9:53 09

Содержание 50038948











































































Результаты поиска

Содержание 50038948

Отзывы:

Бренды по названию

Популярные бренды

Leuze electronic 50038948, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50038948

Отзывы:

Бренды по названию

Популярные бренды