Leuze electronic 50038948 Скачать руководство пользователя страница 56

Страница: 56 / 74

Important parameters

BCL 8

Leuze electronic

10.6

Switching input tab

Figure 10.8: Switching input tab

Inverted

Here, the input level can be inverted

Release

Switching input enabled or disabled

Debounce time

This time period must lapse until the trigger signal is regarded as

valid.

Switch-on delay

The trigger signal is passed on delayed by the specified time period.

Pulse duration

If the value is higher than "0": duration of the activation, regardless of

how long the trigger signal has been present.

Switch-off delay

After the end of the trigger signal, the pulse is extended internally by

this time period.

NOTE

If the switch-off delay is activated, the parameter "pulse duration" should be "0".

Function

Event that is started when the switching input is activated.

ATTENTION!

Depending on wiring, either a switching input or a switching output is available on the

BCL 8.

UM_BCL8_de_50040581.book Seite 54 Montag, 24. Februar 2020 9:53 09

Содержание 50038948











































































Результаты поиска

Содержание 50038948

Отзывы:

Бренды по названию

Популярные бренды

Leuze electronic 50038948, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50038948

Отзывы:

Бренды по названию

Популярные бренды