background image

Operation:

Seat:

 Locate the seat slider lever with your right hand under your right thigh and slide the 

seat to the desired position. 

High / Low Speed:

  Located on the left hand side of rear shroud.  Set the Hi/Lo Speed 

switch as desired. Ideally Hi for outdoor use and Lo for indoor use. 

Setting Maximum Speed:

   Set the Speed Control Knob in the middle of the dash 

panel to suit the driving conditions. Slower speeds for indoor use and faster speeds for 
outdoor use.  

Turn On:

  Insert the key and rotate to the on position. If left untouched for 20 minutes the 

scooter will turn off  to save power. 2 Red Leds will show. To restart simply turn the key off 
and then on again. 

Forward:

  Gently depress the control lever with your thumb or pull with your finger as 

desired, to begin driving, The more you depress or pull, the faster  the scooter will go. The 
maximum speed attained is set by the Speed Control Knob.

Reverse:

   As above but in the opposite direction.  A warning beeper will sound. It is 

possible to operate the scooter one handed with either left or right hand. Should you have 
a preference for the controls to operate opposite to the factory setting simply ask your 
dealer to reverse the polarity. 

Stopping:

  Simply release the control lever and the scooter will come to a smooth stop or 

to stop faster push the control lever into reverse. Your scooter features 2 automatic braking 
systems as well as an emergency Electronic stop system. The first  gently slows the 
scooter and the second holds the scooter once stopped. The Electronic brake operates by 
thrusting the throttle lever into reverse. 

Steering

: Smoothly turn the control tiller in the direction you want to go.  On tight turns it 

is suggested the speed control  be set to the slowest speed before turning the tiller 
sharply.

Horn:

  Push the horn button as required using right or left hand. 

Pushing:

 Move the brake release lever located at the rear to the open position. Some 

resistance will be felt from the motor and gearbox. The brake release lvere must be re 
engaged before the scooter can be driven. 

Содержание TS401 Rabbit Scooter











Отзывы: