background image

Technician Service Guide                                                                                                                               33367B

1

PORTABLE SCR REGULATED

BATTERY CHARGER

TECHNICIAN SERVICE GUIDE

PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS

To be able to troubleshoot safely and effectively, it is important

 to read this guide COMPLETELY before beginning any tests.

LOOK FOR THIS SYMBOL TO POINT OUT SAFETY PRECAUTIONS. IT  MEANS:

BECOME ALERT—YOUR SAFETY IS INVOLVED.

  IF YOU DO NOT FOLLOW THESE

SAFETY INSTRUCTIONS, INJURY OR PROPERTY DAMAGE CAN OCCUR.

CAUTION:  REPAIRS BY QUALIFIED

PERSONNEL ONLY.  NOTE:  MODIFYING THIS
CHARGER FOR USE OTHER THAN THAT FOR
WHICH IT WAS INTENDED, REPAIRS BY
PERSONS NOT QUALIFIED, OR NOT USING
ORIGINAL EQUIPMENT REPLACEMENT PARTS
WILL VOID THE MANUFACTURER'S WARRANTY
AND LIABILITY.  INCORRECT REASSEMBLY
MAY RESULT IN A RISK OF ELECTRIC SHOCK
OR FIRE.

CAUTION:  DO NOT EXPOSE CHARGER TO

WATER, RAIN OR POWERWASH.

DANGER:  HAZARD OF ELECTRIC SHOCK!

ALWAYS UNPLUG THE ELECTRICAL CORDS,
FIRST FROM THE AC OUTLET, AND THEN FROM
THE CHARGER RECEPTACLE, BEFORE
ATTEMPTING ANY REPAIRS OR SERVICE TO
THE CHARGER.  TURNING THE CHARGER OFF
DOES NOT REDUCE THIS RISK.

WARNING:  DO NOT OPERATE THE

CHARGER IF IT IS MALFUNCTIONING.
PERSONAL INJURY OR PROPERTY DAMAGE
COULD RESULT.

WARNING:  DO NOT TOUCH THE BATTERY

TERMINALS OR CONTACTS ON THE CHARGING
PLUG.  AN ELECTRIC SHOCK COULD RESULT.

This service guide applies to most portable style
SCR regulated charger designs but not all.  This
service guide does not cover railroad or heavy
industrial styles of chargers.  Please contact the
factory for assistance if there is doubt regarding the
appropriate service guide for a specific model of
charger.

The battery charger is, at most, one third (1/3) of the
complete system, which includes the equipment, the
batteries, and the wiring to/from and between the
batteries.  To locate and correct a problem with
certainty, initial diagnosis and testing must include
all elements of the system.  The charger is
constructed so all parts can be tested and replaced
with basic hand tools.

See the appropriate owners manual, the model
number listed on the owners manual should match
the model number on the faceplate of the charger,
for detailed installation, operating procedures and
safety precautions.  FOLLOW ALL SAFETY
PRECAUTIONS.

*33367*

Содержание 33367













Отзывы: