background image

16 

Trouble Shooting 

 
● 

Verify you have the right power cord or adapter. Never use a power supply or adapter with a 

non-compliant DC output voltage or it will burn the equipment.

 

 
● 

Select  the  proper  UTP  or  STP  cable  in  order  to  construct  the  network.  Use  an  unshielded 

twisted-pair  (UTP)  or  shield  twisted-pair  (STP)  cable  for  RJ-45  connections:  100Ω  Category  5e 

for 10M/100/1000Mbps. Also be sure that the length of any twisted-pair connection does not 

exceed 100 meters (328 feet).

 

 
● 

Diagnosing LED Indicators: To assist in identifying problems, the switch can be easily monitored 

with the LED indicators which help to identity if any problems exist.

 

 

Please refer to the LED Indicators section for LED light indication.

 

 
● 

If the power indicator LED does not turn on when the power cord is plugged in, the user may 

have  a  problem  with  the  power  cord.  Check  for  loose  power  connections,  power  losses  or 

surges at the power outlet.

 

 

Please  contact  Leonton  for  technical  support  service,  if  the  problem  still  cannot  be 

resolved.

 

 
● 

If the industrial switch LED indicators are normal and the connected cables are correct but the 

packets  still  cannot  transmit,  please  check  the  system’s  Ethernet  devices’  configuration  or 

status.

 

Содержание PT2-0802-2C-24 Series






















Отзывы: