Lenze POWERLINK E84DGDV Series Скачать руководство пользователя страница 46

Страница: 46 / 70

Parameter reference

Parameters relevant for POWERLINK communication

Lenze · Decentralised frequency inverter 8400 motec (POWERLINK Option) · EDS84DMOTPL EN 1.0 - 11/2018

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

11.2

Parameters relevant for POWERLINK communication

This chapter lists the POWERLINK parameters of the Communication Unit in numerically ascending

order.

C13000

C13001

C13003

Parameter | Name:

C13000 | 0x1E40.2 IP address

Data type: UNSIGNED_32

Index: 11575

= 2D37

The code displays the IP address of the communication module.

• The IP address is derived from the node address (Node ID):

192.168.100.[Node ID]

• The node ID is derived from the DIP switch setting of the Drive Unit or from

C13899



Node address (node ID) setting (



26)

Display range

(min. value | unit | max. value)

Subcodes

Info

C13000/1

IP address

• Example: 0xC0A86401 = 192.168.100.1



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Parameter | Name:

C13001 | 0x1E40.3 Subnet Mask

Data type: UNSIGNED_32

Index: 11574

= 2D36

The code declares the IP subnet mask which restricts the directly addressable IP address range (i.e. without a gate-

way in the EPL segment of the routers). The value 255.255.255.0 (0xFFFFFF00) is always assigned to the subnet mask

in one segment.

Display range

(min. value | unit | max. value)

Subcodes

Info

C13001/1

EPL IP Subnet Mask

• Lenze setting (hex): 0xFFFFFF00 = 255.255.255.0



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Parameter | Name:

C13003 | 0x1E40.5 IP address router

Data type: UNSIGNED_32

Index: 11572

= 2D34

The code declares the IP address of the router which connects the EPL segment to the higher-level network. The

standard entry corresponds to the standard router address of the EPL specification:



192.168.100.254

Permissible entries replace the lowest-order byte of the standard entry with the EPL address of the node which has

the function of a router.

Setting range

(min. value | unit | max. value)

Subcodes

Lenze setting

Info

C13003/1

3232261374

IP address router

• Lenze setting (hex): 0xC0A864FE = 192.168.100.254



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Содержание POWERLINK E84DGDV Series







































































Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды

Lenze POWERLINK E84DGDV Series, Руководство по связи

Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды