Lenze POWERLINK E84DGDV Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 70

background image

Installation

Electrical installation

24

Lenze · Decentralised frequency inverter 8400 motec (POWERLINK Option) · EDS84DMOTPL EN 1.0 - 11/2018

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

5.2.5

External voltage supply

• The external voltage supply can be used to establish POWERLINK communication for

commissioning and to query the data of the digital and analog inputs.

• Furthermore the external voltage supply serves to maintain POWERLINK communication if the

main supply fails.

• The digital inputs RFR, DI1 ... DI5 and the analog input can continue to be evaluated.
• The external voltage supply is done via the terminals 24E and GND of the terminal strip X3.
• Permissible voltage (DC) / max. current:

• U = 24 V DC (20 V - 0 % ... 29 V + 0 %)
• I

max

= 120 mA

• Access to parameters of a device that is disconnected from the mains is not possible.



Hardware manual for the Inverter Drive 8400 motec

Here you can find detailed information on how to wire the Communication Unit.

«
...
22
23
24
25
26
...
»

Содержание POWERLINK E84DGDV Series







































































Отзывы:

Нет отзывов

Похожие инструкции для POWERLINK E84DGDV Series

Бренд: Festo Страницы: 16

Compax3H C3H1xxV4 Series

Бренд: Parker Страницы: 44

Бренд: Fagor Страницы: 60

Бренд: Festo Страницы: 12

Бренд: HAUTAU Страницы: 20

Бренд: HAUTAU Страницы: 16

DVD+/-RW Slim External Drive

Бренд: Targus Страницы: 13

COMBIVERT Series

Бренд: KEB Страницы: 124

CDC-TW-0502-0500-1-ACB

Бренд: Dyer Страницы: 8

Бренд: FOTEK Страницы: 171

Бренд: Technosoft Страницы: 90

iPOS4808 MX Series

Бренд: Technosoft Страницы: 114

Бренд: D+H Страницы: 32

Бренд: TeMec Drive Страницы: 52

Бренд: YASKAWA Страницы: 610

Бренд: Lenze Страницы: 199

Бренд: Samsung Страницы: 30

Бренд: Eaton Страницы: 199

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды