Lenze POWERLINK E84DGDV Series Скачать руководство пользователя страница 17

Страница: 17 / 70

Lenze · Decentralised frequency inverter 8400 motec (POWERLINK Option) · EDS84DMOTPL EN 1.0 - 11/2018

Technical data

POWERLINK communication data

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

4.2

POWERLINK communication data

Communication time

The communication time is the time between the start of a request and the arrival of the

corresponding response.
The communication times in an POWERLINK network depend on the ...

• processing time in the inverter;
• frame runtime (baud rate / frame length);
• nesting depth of the network.

Processing time inside the inverter

There are no interdependencies between parameter data and

process data

Range

Values

Min. cycle time

400

Total cycle times

0.4 / 0.5 / 1.0 / 1.2 / 2.0 / 3.0 … 20.0 ms

Buffer size

• Tx-iso: max. 1490 bytes

• Rx-iso: max. 1490 bytes

Delay time

• Controlled node (T

Preq

- T

Res

): approx. 2.6

• Controlled node (T

SoA

- T

ASnd

): approx. 2.6

Frame size

Max. asynchronous frame size (MTU): 1518 bytes

SDO communication method

UDP/IP or ASND

Number of RPDOs

1 channel

RPDO user data per application

Max. 6 objects (max. 10 bytes)

Number of TPDOs

1 channel (data access of all nodes by broadcasting)

TPDO user data per application

Max. 6 objects (12 bytes)

CN operating modes

Support of ...

• Multiplex CNs

• Optional CNs

Data

Processing time

Process data

Approx. 2 ms

+ 0 ... 1 ms

+ 1 ... x ms

Update cycle

Processing time in the module

Runtime of the application task of the technology

application used (tolerance)

Parameter data

Approx. 30 ms + a tolerance of 20 ms (typically)

Some codes may require a longer processing time (see reference manual/

online help for Inverter Drive 8400 motec).

Содержание POWERLINK E84DGDV Series







































































Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды

Lenze POWERLINK E84DGDV Series, Руководство по связи

Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды