Lenze I/O system 1000 Скачать руководство пользователя страница 361

Страница: 361 / 583

EtherCAT communication

7.7

Parameterising the counter

361

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

7.7.4

2 counters 32 bits, 24 V DC - EPM-S603

The following functions can be parameterised:

Further information:

Parameter data

Counting functions

Description

Continuous counting The counter counts from 0 to the counting limit, then skips to the opposite counting limit

and continues to count from there.

Signal evaluation

Description

Single rotary

transducer

Connection to "A/pulse" input

Double rotary

transducer
Quadruple rotary

transducer

Connection to input "A/pulse" and "B/direction"

Direction

Pulse at "A/pulse" input and direction at "B/direction" input

Additional functions Description

Gate function

The gate function serves to start, stop, and interrupt a counting function. In the case of this

counter the internal gate (I-gate) is conform to the software gate (SW gate) which you

control via your user program (status word in the output area).

Subindex Name

Description/value

Lenze

Input frequency

Counter 1, track A

Filters for instance serve to filter signal peaks in the case of an

unclean input signal.

0 (0x00): 500 kHz

1 (0x01): 300 kHz

2 (0x02): 100 kHz

3 (0x03): 60 kHz

4 (0x04): 30 kHz

6 (0x06): 10 kHz

7 (0x07): 5 kHz

8 (0x08): 2 kHz

9 (0x09): 1 kHz

Other values are not permissible!

0x02

Input frequency

Counter 1, track B

0x02

Input frequency

Counter 2, track A

0x02

Input frequency

Counter 2, track B

0x02

Counting direction

counter 1, track B

Bit 2 ... 0: Reserved

Bit 3: Invert counting direction track B

0 = no (do not invert)

1 = yes (invert)

Bit 7 ... 4: Reserved

0x00

Signal evaluation

counter 1*

Bit 2 ... 0: Signal evaluation

• 0b000 = counter deactivated (the other parameter data

details for the counter are ignored)

• 0b001 = rotary transducer 1-fold (connection to "A/pulse"

input)

• 0b010 = rotary transducer 2-fold (connection to "A/pulse"

input)

• 0b011 = rotary transducer 4-fold (connection to "A/pulse"

input and "B/direction")

• 0b100 = direction (pulse at "A/pulse" input and direction at

"B/direction" input)

Bit 7 ... 3: Reserved

0x00

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание I/O system 1000

Отзывы:

Lenze I/O system 1000, Справочное руководство, Страница: 361 / 583

Результаты поиска

Содержание I/O system 1000

Отзывы: