Lenze E84DGFCp Series Скачать руководство пользователя

Страница: 35 / 100

EDS84DMOTPBUS EN 3.0 - 11/2011

Communication manual 8400 motec PROFIBUS

Process data transfer

Access to process data / PDO mapping

Process data transfer

8.1

Access to process data / PDO mapping

Process data are transferred via the MCI/CAN interface.



Max. 8 words (16 bits/word) per direction can be exchanged.



The process data are accessed via the port blocks

LP_Network_In

and

LP_Network_Out

. These port blocks are also called process data channels.



The port/function block interconnection of the process data objects (PDO) takes place

via the Lenze »Engineer«.

[8-1]

External and internal data transfer between bus system, controller, and application



Software manual / »Engineer« online help "Inverter Drives 8400 motec"

Here you will find detailed information on port blocks and port/function block

interconnection in the »Engineer«.

Содержание E84DGFCp Series





































































































Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды

Lenze E84DGFCp Series, Руководство по связи

Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды