Lenze AC Tech MC3000 Series Скачать руководство пользователя страница 3

Страница: 3 / 17

RG-MCMET

Contents

1 Safety Information .............................................................................................................1

1.1

Warnings, Cautions and Notes ..............................................................................1
1.1.1  General ....................................................................................................1
1.1.2  Application ...............................................................................................1
1.1.3  Installation ...............................................................................................1
1.1.4  Electrical Connection ................................................................................2
1.1.5  Operation .................................................................................................2

2 Introduction .......................................................................................................................3

2.1

Metasys N2 Communications ................................................................................3

2.2

Serial Communications Wiring ..............................................................................3

3 Drive Setup and Programming ...........................................................................................4

3.1

Serial Communication Setup .................................................................................4

3.2

Communication Overrides .....................................................................................5

4 MC3000 N2 Points ............................................................................................................6

4.1

Metasys N2 Point Map ..........................................................................................7

4.2

Analog Input (AI) Point Descriptions .......................................................................8

4.3

Binary Input (BI) Point Descriptions .......................................................................11

4.4

Analog Output (AO) Point Descriptions ...................................................................11

4.5

Binary Output (BO) Point Descriptions ...................................................................13

4.6

Reference and Links .............................................................................................13

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание MC3000 Series


















Результаты поиска

Содержание MC3000 Series

Отзывы:

Похожие инструкции для MC3000 Series

Бренды по названию

Популярные бренды

Lenze AC Tech MC3000 Series, Руководство по связи

Результаты поиска

Содержание MC3000 Series

Отзывы:

Похожие инструкции для MC3000 Series

Бренды по названию

Популярные бренды