Lenovo x3250 m6 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 696

background image

Antes de instalar este producto, lea la información de seguridad.

Läs säkerhetsinformationen innan du installerar den här produkten.

Bu ürünü kurmadan önce güvenlik bilgilerini okuyun.

Guidelines for trained service technicians

This section contains information for trained service technicians.

Inspecting for unsafe conditions

Use this information to help you identify potential unsafe conditions in a device that you are working on.

Each device, as it was designed and manufactured, has required safety items to protect users and service
technicians from injury. The information in this section addresses only those items. Use good judgment
to identify potential unsafe conditions that might be caused by unsupported alterations or attachment of
unsupported features or optional devices that are not addressed in this section. If you identify an unsafe
condition, you must determine how serious the hazard is and whether you must correct the problem before
you work on the product.

Consider the following conditions and the safety hazards that they present:

• Electrical hazards, especially primary power. Primary voltage on the frame can cause serious or fatal

electrical shock.

• Explosive hazards, such as a damaged CRT face or a bulging capacitor.

• Mechanical hazards, such as loose or missing hardware.

To inspect the product for potential unsafe conditions, complete the following steps:

1. Make sure that the power is off and the power cords are disconnected.

2. Make sure that the exterior cover is not damaged, loose, or broken, and observe any sharp edges.

3. Check the power cords:

• Make sure that the third-wire ground connector is in good condition. Use a meter to measure

third-wire ground continuity for 0.1 ohm or less between the external ground pin and the frame ground.

• Make sure that the power cords are the correct type.

• Make sure that the insulation is not frayed or worn.

4. Remove the cover.

vi

Lenovo System x3250 M6 Installation and Service Guide

«
...
6
7
8
9
10
...
»

Содержание x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для x3250 m6

SuperServer E100-8Q

Бренд: Supermicro Страницы: 48

x3655 - System - 7985

Бренд: IBM Страницы: 118

Sun Blade T6340

Бренд: Sun Oracle Страницы: 82

Бренд: Axis Страницы: 10

Flex System p270 Compute Node

Бренд: IBM Страницы: 510

NPort P5250A Series

Бренд: Moxa Technologies Страницы: 2

SuperServer E300-9A-4C

Бренд: Supermicro Страницы: 109

Бренд: LiveU Страницы: 14

Бренд: TYAN Страницы: 70

Бренд: Intermec Страницы: 232

DIGI CONNECT ES

Бренд: Digi Страницы: 23

Бренд: Hitachi Страницы: 57

Бренд: Hitachi Страницы: 76

BladeSymphony 1000

Бренд: Hitachi Страницы: 52

Бренд: Hitachi Страницы: 91

Бренд: Hitachi Страницы: 174

HVM Navigator V03-06

Бренд: Hitachi Страницы: 312

NVM Navigator v03-07

Бренд: Hitachi Страницы: 316

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды