background image

39

Lenovo V14 and V15 Hardware Maintenance Manual

FRU replacement notices

This section presents notices related to removing and replacing parts. Read 

this section carefully before replacing any FRU.

Screw notices 

Loose screws can cause a reliability problem. In the Lenovo computer, this 

problem is addressed with special nylon-coated screws that have the following 

characteristics:
•  They maintain tight connections.
•  They do not easily come loose, even with shock or vibration.
•  They are harder to tighten.
•  Each one should be used only once.

Do the following when you service this machine: 
•  Keep the screw kit in your tool bag.
•  Carefully remove screws for reuse when replacing FRU.
•  Use a torque screwdriver if you have one.

Tighten screws as follows:
• 

Plastic to plastic

  Turn an additional 90° after the screw head touches the surface of the 

plastic part:

more than 90°

(Cross-section)

• 

Logic card to plastic 

  Turn an additional 180° after the screw head touches the surface of the 

logic card: 

more than 180°

(Cross-section)

• 

Torque driver 

  If you have a torque screwdriver , refer to the “Torque” column for each step.
•  Make sure that you use the correct screws. If you have a torque screwdriver, 

tighten all screws firmly to the torque shown in the table. 

Carefully remove 

screws for reuse when replacing FRU. Make sure that all screws are 

tightened firmly.

•  Ensure  torque  screwdrivers  are  calibrated  correctly  following  country 

specifications.

Содержание V14










































































Отзывы: