Lenovo ThinkSystem SR550 Скачать руководство пользователя страница 92

Страница: 92 / 206

A video of this procedure is available at

https://www.youtube.com/playlist?list=PLYV5R7hVcs-

C9jFjZnXQ6AmTXaIdX6_HJ

Figure 61. 3.5-inch-drive backplane installation

Step 1. Connect the cables to the backplane and align the backplane with the chassis and lower it into the

chassis. Put the backplane into the front of the posts on the chassis with it leaning backward
slightly.

Step 2. Rotate the backplane to vertical position to ensure that the four hooks on the chassis pass through

the corresponding holes in the backplane. Then, slide the new backplane as shown until it is
secured into place.

After installing the backplane;

1. Reinstall drives or drive fillers.
2. Complete the parts replacement. See “Complete the parts replacement” on page 164.

Remove the 2.5-inch-drive backplane

Use this information to remove the 2.5-inch-drive backplane.

Static Sensitive Device

Ground package before opening”

on page 56

Before removing the backplane:

ThinkSystem SR550 Maintenance Manual

Содержание ThinkSystem SR550















































































































































































































Результаты поиска

Содержание ThinkSystem SR550

Отзывы:

Похожие инструкции для ThinkSystem SR550

Бренды по названию

Популярные бренды

Lenovo ThinkSystem SR550, Руководство по обслуживанию

Результаты поиска

Содержание ThinkSystem SR550

Отзывы:

Похожие инструкции для ThinkSystem SR550

Бренды по названию

Популярные бренды