Lenovo ThinkSystem SR550 Скачать руководство пользователя страница 180 | Manualshive

Страница: 180 / 206

background image

• Power supplies

5. If you just installed an optional device, remove it, and restart the server. If the server starts, you might

have installed more devices than the power supply supports.

Server does not power on

Complete the following steps until the problem is resolved:

1.  Check the event log for any events related to the server not powering on.
2.  Check for any LEDs that are flashing amber.
3.  Check the power LED on the system board.
4.  Reseat the power supply.
5.  Replace the power supply.

Server does not power off

Complete the following steps until the problem is resolved:

1. Determine whether you are using an Advanced Configuration and Power Interface (ACPI) or a non-ACPI

operating system. If you are using a non-ACPI operating system, complete the following steps:
a. Press

Ctrl+Alt+Delete

.

b.  Turn off the server by pressing the power button and holding it down for 5 seconds.
c.  Restart the server.
d.  If the server fails POST and the power button does not work, disconnect the power cord for 20

seconds; then, reconnect the power cord and restart the server.

2. If the problem remains or if you are using an ACPI-aware operating system, suspect the system board.

Memory problems

Use this information to resolve issues related to memory.

• “Displayed system memory less than installed physical memory” on page 172
• “Multiple rows of DIMMs in a branch identified as failing” on page 173

Displayed system memory less than installed physical memory

Complete the following steps until the problem is resolved:

Note:

Each time you install or remove a DIMM, you must disconnect the server from the power source; then,

wait 10 seconds before restarting the server.

1. Make sure that:

•  No error LEDs are lit on the operator information panel.
•  No DIMM error LEDs are lit on the system board.
•  Memory mirrored channel does not account for the discrepancy.
•  The DIMMs are seated correctly.
•  You have installed the correct type of memory.
•  If you changed the memory, you updated the memory configuration in the Setup utility.
•  All banks of memory are enabled. The server might have automatically disabled a memory bank when

it detected a problem, or a memory bank might have been manually disabled.

• There is no memory mismatch when the server is at the minimum memory configuration.

2. Reseat the DIMMs, and then restart the server.

172

ThinkSystem SR550 Maintenance Manual

«
...
178
179
180
181
182
...
»

Содержание ThinkSystem SR550















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkSystem SR550

Бренд: Makita Страницы: 3

Бренд: Panasonic Страницы: 172

Бренд: MAC TOOLS Страницы: 44

Бренд: ITech Страницы: 46

Бренд: Microtec Страницы: 6

Бренд: Sanela Страницы: 2

Бренд: THERMOBILE Страницы: 66

Бренд: Xtreme Страницы: 10

Бренд: Batavia Страницы: 46

Бренд: unicraft Страницы: 16

Gardtec 500 series

Бренд: GARDINER TECHNOLOGY Страницы: 40

LI-HOME2V IMPACT218

Бренд: Valex Страницы: 16

Бренд: Surtek Страницы: 16

Бренд: Banner Страницы: 2

Torque Screwdrivers BE-6990-AH

Бренд: Bahco Страницы: 2

Бренд: TekPower Страницы: 4

Autronic ACR Series

Бренд: Forte Страницы: 2

Бренд: multicomp pro Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды