Lenovo ThinkSystem SR550 Скачать руководство пользователя страница 140

Страница: 140 / 206

Step 2. Align the memory module with the slot, and gently place the memory module on the slot with both

hands.

Step 3. Firmly press both ends of the memory module straight down into the slot until the retaining clips

snap into the locked position.

Note:

If there is a gap between the memory module and the retaining clips, the memory module

has not been correctly inserted. Open the retaining clips, remove the memory module, and then
reinsert it.

After installing the memory module, complete the parts replacement. See “Complete the parts replacement”
on page 164.

LOM adapter replacement

Use this information to remove and install the LOM adapter.

Remove the LOM adapter

Use this information to remove the LOM adapter.

Static Sensitive Device

Ground package before opening”

on page 56

Before removing the LOM adapter, remove the top cover. See “Remove the top cover” on page 56.

To remove the LOM adapter, complete the following steps:

Watch the procedure

A video of this procedure is available at

https://www.youtube.com/playlist?list=PLYV5R7hVcs-

C9jFjZnXQ6AmTXaIdX6_HJ

132

ThinkSystem SR550 Maintenance Manual

Содержание ThinkSystem SR550















































































































































































































Результаты поиска

Содержание ThinkSystem SR550

Отзывы:

Похожие инструкции для ThinkSystem SR550

Бренды по названию

Популярные бренды

Lenovo ThinkSystem SR550, Руководство по обслуживанию

Результаты поиска

Содержание ThinkSystem SR550

Отзывы:

Похожие инструкции для ThinkSystem SR550

Бренды по названию

Популярные бренды