background image

 

© Copyright Lenovo 2020 

  ThinkSystem 440-16e SAS/SATA PCIe Gen4 12Gb HBA Installation and User Guide 

Chapter 2:  Adapter Installation Instructions 

This chapter provides detailed instructions on how to install your adapter. To install the adapter, follow these steps: 
1.  Unpack your adapter. 

Unpack and remove the adapter. Inspect the adapter for damage. 

ATTENTION 

To avoid the risk of data loss, back up your data before you change your system configuration. 

2.  Turn off the power to the system. 

Turn off the power to the computer, and disconnect the AC power cord. Remove the computer cover. Refer to the 

system documentation for instructions. Before you install the adapter, make sure that the computer is disconnected 

from the power and from any networks. 

CAUTION 

Disconnect the computer from the power supply and from any networks to which you will install 

the adapter, or you risk damaging the system or experiencing electrical shock. 

3.  Review the adapter connectors. 
4.  Check the mounting bracket on the adapter. 

If required for your system, replace the full-profile mounting bracket that ships on the adapter with the low-profile 

bracket supplied. Complete the following steps to attach the low-profile bracket. 
a.  Using a No. 1 Phillips screwdriver that is ESD safe, remove the two Phillips screws that connect the full-profile 

bracket to the board. Unscrew the two screws located at the top and bottom edges of the board. Avoid touching 

any board components with the screwdriver or the bracket. 

b.  Remove the full-profile bracket. Do not damage the adapter. 
c.  Place the adapter on top of the low-profile bracket. Position the bracket so that the screw holes in the tabs align 

with the openings in the board. 

d.  Using a No. 1 Phillips torque screwdriver that is ESD safe, set to a maximum torque of 4.8 ± 0.5 inch-pounds. 

Replace the two Phillips screws removed in Step a. 

ATTENTION 

Exceeding this torque specification can damage the board, connectors, or screws, and can void 

the warranty on the board. Damage caused to the board as a result of changing the bracket can 

void the warranty on the board. Adapters returned without a bracket mounted on the board will be 

returned without return merchandise authorization (RMA) processing. 

5.  Insert the adapter into an available PCIe slot. Select a PCIe slot, and align the adapter’s PCIe bus connector to the 

slot, as shown in the following figure. Press down gently, but firmly, to make sure that the adapter is seated correctly 

in the slot. Secure the bracket to the computer chassis with the bracket screw. 
Refer t

ThinkSystem Server Documentation Center

, select your product, and review the Install server hardware 

options section for detailed instructions 

NOTE 

Adapters with a x8 host interface can operate in x8 or x16 slots. However, some x16 PCIe slots 

support only PCIe graphics cards; an adapter installed in one of these slots will not function. Refer to 

the guide for your motherboard for information about the PCIe slots. 

ATTENTION 

The shape, size, and locations of the components on your adapter and its bracket might vary 

from the following illustration. 

Содержание ThinkSystem 440-16e













Отзывы: