Lenovo ThinkStation P500 Скачать руководство пользователя страница 92

Страница: 92 / 232

Problems with the keyboard or mouse

This section provides solutions to keyboard-related and mouse-related problems.

The mouse does not work

Solutions:

• Connect the mouse cable to a USB connector or PS/2 mouse connector.

Note:

Depending on your keyboard, integrated USB connectors might be available to be used to

connect a USB mouse.

• Install the device drivers for the mouse.

• If you are using a USB mouse, enable the USB connectors in the BIOS settings. For more information,

see “Enabling or disabling a device” on page 67.

The pointer on the screen does not move smoothly with the mouse

Solution: Clean the mouse. For more information, see “Optical mouse” on page 78.

The fingerprint reader on the keyboard does not work

Solutions:

• Enroll your fingerprint correctly.

• Never scratch the surface of the reader with a hard, pointed object.

• Never scrap the surface of the reader with your nail or anything hard.

• Use or touch the reader with a clean finger.

• Ensure that the surface of your finger is the same with the one when you last enrolled.

The wireless keyboard does not work

Solutions:

• If the transceiver communications LED is not on, reconnect the transceiver and the keyboard.

• If the wireless keyboard does not work when the transceiver communications LED is on, restart your

computer.

If the problem persists after the restart, ensure that:

• The batteries are installed correctly.

• The batteries still retain their current.

• The distance from the wireless keyboard to the transceiver is less than 10 m (393.7 inches).

• The transceiver is installed fully.

Monitor problems

This section provides solutions to monitor-related problems.

My screen goes blank while the computer is on

Solutions: Your screen saver or power management might have been enabled. Do one of the following:

• Press a key to exit the screen saver.

• Press the power button to resume the computer from sleep or hibernation mode.

ThinkStation P500 and P700 Hardware Maintenance Manual

Содержание ThinkStation P500









































































































































































































































Результаты поиска

Содержание ThinkStation P500

Отзывы:

Lenovo ThinkStation P500, Руководство по техническому обслуживанию аппаратной части, Страница: 92 / 232

Результаты поиска

Содержание ThinkStation P500

Отзывы: