Lenovo ThinkStation P500 Скачать руководство пользователя страница 73

Страница: 73 / 232

3. Depending on the password type, select

Set Power-On Password

Set Administrator Password

, or

Hard Disk Password

4. Follow the instructions on the right side of the screen to set, change, or delete a password.

Note:

A password can be any combination of up to 64 alphabetic and numeric characters. For more

information, see “Password considerations” on page 66.

Erasing lost or forgotten passwords (clearing CMOS)

This section provides instructions on how to erase lost or forgotten passwords, such as a user password.

To erase a lost or forgotten password, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 111.

3. Locate the Clear CMOS /Recovery jumper on the system board. See “Locating parts on the system

board” on page 35.

4. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and

pin 3).

5. Reinstall the computer cover and connect the power cord. See “Completing the parts replacement” on

page 198.

6. Turn on the computer and leave it on for approximately 10 seconds. Then, turn off the computer by

holding the power button for approximately five seconds.

7. Repeat step 1 through step 2.

8. Move the Clear CMOS /Recovery jumper back to the standard position (pin 1 and pin 2).

9. Reinstall the computer cover and connect the power cord. See “Completing the parts replacement” on

page 198.

Enabling or disabling a device

This section provides information on how to enable or disable user access to the following devices:

USB Setup

Use this option to enable or disable a USB connector. When a USB connector is
disabled, the device connected to the USB connector cannot be used.

SATA Controller

When this option is set to

Disable

, all devices connected to the SATA connectors

(such as hard disk drives or optical drives) are disabled and cannot be accessed.

To enable or disable a device, do the following:

1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 65.

2. From the Setup Utility program main menu, select

Devices

3. Depending on the device you want to enable or disable, do one of the following:

• Select

USB Setup

to enable or disable a USB device.

• Select

ATA Drive Setup

to enable or disable an internal or external SATA device.

4. Select the desired settings and press Enter.

5. Press F10 to save changes and exit the Setup Utility program. See “Exiting the Setup Utility program”

on page 69.

Chapter 6

Advanced configuration

Содержание ThinkStation P500









































































































































































































































Результаты поиска

Содержание ThinkStation P500

Отзывы:

Lenovo ThinkStation P500, Руководство по техническому обслуживанию аппаратной части, Страница: 73 / 232

Результаты поиска

Содержание ThinkStation P500

Отзывы: