Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 20

Страница: 20 / 130

Table 2. Features and specifications

Microprocessor:

Your server comes with one of the following
microprocessors (internal cache size varies by model
type):

• Intel

Xeon

quad-core microprocessor

• Intel Xeon dual-core microprocessor

• Intel Pentium

dual-core microprocessor

• Intel Celeron

dual-core microprocessor

• Intel Core

™

i3 microprocessor

For the specific type and speed information about the
microprocessor, use the Setup Utility program. See
“Using the Setup Utility program” on page 63.

For a list of the ThinkServer microprocessor options, go to
http://www.lenovo.com/thinkserver. Click the

Products

tab, which is in the middle area of the Web page. Then,
click

Options

➙

ThinkServer Processors

to view the

information.

Memory

• Your server has four memory slots.

• Each slot supports 2 GB and 4 GB 1333 MHz double

data rate 3 (DDR3) unbuffered dual inline memory
modules (UDIMMs) with or without the Error Checking
and Correcting (ECC) technology.

• Each slot supports 8 GB 1333 MHz DDR3 UDIMMs

with the ECC technology.

Internal drives

• Serial Advanced Technology Attachment (SATA) hard

disk drive

• SATA optical drive

Video subsystem

Integrated graphics for a Video Graphics Array (VGA)
connector and a DisplayPort connector

Connectivity

• 100/1000 Mbps integrated Ethernet controller

Power supply assembly:

Your server comes with a 280-watt auto-sensing power
supply assembly.

Note:

If you are using uninterruptible power supplies

(UPS), ensure that you use only pure-sine UPSes with
your ThinkServer server.

Expansion

• Two optical drive bays

System management features

• Ability to store power-on self-test (POST) hardware

test results

• Automatic power-on startup

• Intel Active Management Technology (AMT)

• Intel Hyper-Threading technology (some models)

• Intel Rapid Storage Technology (RST)

• Preboot Execution Environment (PXE)

• System Management (SM) UEFI and SM software

• Wake on LAN

• Wake on Ring (in the Setup Utility program, this feature

is called Serial Port Ring Detect for an external modem)

Input/Output (I/O) features

• Eight Universal Serial Bus (USB) connectors (two on

the front panel and six on the rear panel)

• One 9-pin serial port

• One Ethernet connector

• One DisplayPort connector

• One VGA monitor connector

• Three audio connectors on the rear panel (audio line-in

connector, audio line-out connector, and microphone
connector)

Preinstalled operating system

Some models are preinstalled with one of the following
operating systems:

• Microsoft Windows Server

2008 R2

Foundations/Standard (x64)

• Microsoft Windows Small Business Server 2011

Essentials/Standard

Supported operating systems:

• Microsoft Windows Server 2003 R2

Standard/Enterprise (x86 and x64)

• Microsoft Windows 7 Professional/Ultimate (Service

Pack 1) (x86 and x64)

• Microsoft Windows Server 2008 Foundations (x64)

• Microsoft Windows Server 2008 Standard/Enterprise

(x86 and x64)

• Microsoft Windows Server 2008 R2

Foundations/Standard/Enterprise (x64)

• Microsoft Windows Server 2008 R2

Foundations/Standard/Enterprise (Service Pack
1) (x64)

• Microsoft Windows Small Business Server 2011

Essentials/Standard

• Microsoft Windows Multipoint Server 2011

ThinkServer TS130 Hardware Maintenance Manual

Содержание ThinkServer TS130 1098



































































































































Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды

Lenovo ThinkServer TS130 1098, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды