background image

9.  Turn on the computer; then press and hold the ‘F1’ key until the “Easy-Setup” menu 

appears. 

10.  If the computer presents a password prompt type in the correct password. 
11.  Select ‘Config’ then select ‘Initialize’. 
12.  Select ‘OK’ to initialize the system.  Then click ‘Exit’. 
13.  Select ‘Restart’, and then select ‘OK’ to restart your computer.  
 
 

Section 2:  Using the System Program Service Diskette for ThinkPad 390, 390E, 390X 

models 

 
After creating the System Program Service Diskette, please follow these instructions: 
 
Note:  You need an AC adapter and a fully charged battery pack to update the computer BIOS. 
 
1.  Firmly connect the AC adapter to the computer. 
2.  Insert the System Program Service Diskette into the diskette drive, and then turn on the 

computer. 

3.  Press ‘1’ to update your computer BIOS. 
4.  When the computer displays this message “System program has been updated 

successfully.”, remove the System Program Service Diskette from the diskette drive then 
turn off and restart your computer. 

 

Warning:

 Do not turn off your computer until the update has completed. IF YOU TURN 

OFF YOUR COMPUTER WHILE THE UPDATE IS IN PROGRESS, THE SYSTEM 
BOARD MIGHT HAVE TO BE REPLACED. 

 
After the BIOS update, perform the following steps to make the changes effective: 
 
5.  Turn on your computer and press 'F1' to enter the "IBM BIOS Setup Utility". 
6.  If the computer presents a password prompt, type in the correct password. 
7.  Press the 'F9' key.  Select [Yes] in the “Setup Confirmation" window to load the default 

configuration.  

8.  Press the 'F10' key.  Select [Yes] in the "Setup Confirmation" window to save 

configuration changes and exit the “IBM BIOS Setup Utility”. 

   
 

Section 3:  Using the System Program Service  Diskette for ThinkPad i Series models 

 
After creating the System Program Service Diskette, please follow these instructions: 
 
Note:  You need an AC adapter and a fully charged battery pack to update the computer BIOS. 
 
1.  Firmly connect the AC adapter to the computer. 
2.  Insert the System Program Service Diskette into the diskette drive, and then turn on the 

computer. 

3.  Press ‘1’ to update your computer BIOS.  Follow the instructions on the screen. 
4.  Remove the System Program Service Diskette disk from the diskette drive, turn off, and 

restart your computer. 

 

Warning:

 Do not turn off your computer until the update has completed. IF YOU TURN 

OFF YOUR COMPUTER WHILE THE UPDATE IS IN PROGRESS, THE SYSTEM 
BOARD MIGHT HAVE TO BE REPLACED. 

 
After the BIOS update, perform these steps to make the changes effective: 

Содержание ThinkPad 390







































































Отзывы: