Lenovo ThinkCentre M600 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 142

Lenovo ThinkCentre M600 Скачать руководство пользователя страница 117

Figure 57. Installing the internal speaker holder

14. Align the five screw holes in the system board with the corresponding holes in the chassis. Then, install

the five screws to secure the system board to the chassis.

15. Route all the cables that you disconnected from the system board, and then connect the cables to the

system board. See “Parts on the system board” on page 34.

16. Install the Wi-Fi card. See “Replacing the Wi-Fi card” on page 100.

17. Install the antenna bracket. See “Replacing the antenna bracket” on page 106.

18. Install the front Wi-Fi antenna. See “Replacing the front Wi-Fi antenna” on page 102.

19. Install the internal speaker. See “Replacing the internal speaker” on page 96.

20. Install the memory module. See “Replacing the memory module” on page 95.

21. Install the heat sink. See “Replacing the heat sink” on page 89.

22. Install the computer cover. See “Completing the parts replacement” on page 111.

23. Connect the external cables and the power cord to the computer.

Completing the parts replacement

After completing the installation or replacement for all parts, reinstall the computer cover and reconnect
cables. Depending on the parts you installed or replaced, you might need to confirm the updated information
in the Setup Utility program. Refer to “Using the Setup Utility program” on page 55.

To reinstall the computer cover and reconnect cables to your computer, do the following:

1. Ensure that all components have been reassembled correctly and that no tools or loose screws are

left inside your computer. See “Computer components” on page 31 for the locations of various
components in your computer.

2. Ensure that the cables are routed correctly before reinstalling the computer cover. Keep cables clear of

the hinges and sides of the computer chassis to avoid interference with reinstalling the computer cover.

3. Position the computer cover on the chassis so that the rail guides on the bottom of the computer

cover engage the rails on the chassis. Then, push the cover to the rear of the computer until it snaps
into position.

.

Installing or replacing hardware

111

«
...
115
116
117
118
119
...
»

Содержание ThinkCentre M600















































































































































Отзывы:

Нет отзывов