Lenovo ThinkAgile VX 4-Socket 4U Certified Node Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 296

background image

Step 6. Route and connect the data cables. See “Cable routing for drives” on page 45.

• Route each SAS data cable to its connector on the RAID adapter; then, connect the SAS cable.
• Route each NVMe data cable to its connector on a system board or optional storage tray; then,

connect the NVMe cable.

Step 7. Make sure that all power cables are connected to the storage interposer.
Step 8. Make sure that all of the cables are correctly routed after they have been connected.

After you install a hard disk drive backplane:

1.  Install the fan cage. See “Install a fan cage (upper tray)” on page 125.
2.  Turn the tray right-side up.
3.  Install the upper compute tray or storage tray. See “Install a compute tray” on page 117 or “Install the

storage tray (fully removed)” on page 234.

4. Install any hard disk drives that you removed from the upper tray. Each drive should be installed in its

original location. See “Install a hot-swap drive” on page 148.

5. Install the front cover. See “Install the front cover” on page 132.

Install a hard disk drive backplane (lower tray)

Hard disk drive backplanes in the lower compute tray are accessed from the front of the server. There are

several types of hard disk drive backplane. Steps that are backplane specific are noted in each procedure.

S002

CAUTION:
The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

” on page 89 “

CAUTION:
Make sure that all server power cords are disconnected from their power sources before performing
this procedure.

Complete the following steps to install a hard disk drive backplane in the lower compute tray.

Watch the procedure

. A video of the replacement process is available:

•

•

Step 1. Connect the power and data cables to the hard disk drive backplane. See “Cable routing for drives”

.

Hardware replacement procedures

145

«
...
153
154
155
156
157
...
»

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

Бренд: Z Microsystems Страницы: 17

Бренд: Zonet Страницы: 33

301160U - 1TB Ethernet Disk RAID Network Attached...

Бренд: LaCie Страницы: 5

Бренд: Buffalo Страницы: 80

SUPERSERVER 1018D-73MTF

Бренд: Supero Страницы: 124

Бренд: Hitachi Страницы: 57

Бренд: Hitachi Страницы: 76

BladeSymphony 1000

Бренд: Hitachi Страницы: 52

Бренд: Hitachi Страницы: 91

Бренд: Hitachi Страницы: 174

HVM Navigator V03-06

Бренд: Hitachi Страницы: 312

NVM Navigator v03-07

Бренд: Hitachi Страницы: 316

Бренд: Hitachi Страницы: 129

Бренд: Hitachi Страницы: 466

Бренд: Hitachi Страницы: 530

Бренд: D-Link Страницы: 40

PRIMERGY RX200 S6

Бренд: Fujitsu Страницы: 84

Бренд: NewTek Страницы: 206

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды