Lenovo ThinkAgile VX 4-Socket 4U Certified Node Скачать руководство пользователя страница 142

Страница: 142 / 296

Figure 70. Front cover removal

Step 1. Press release buttons at either side of the front cover.
Step 2. Pull the cover forward and remove it from the server.

After you remove the front cover:

• If you are instructed to return the front cover, follow all packaging instructions, and use any packaging

materials for shipping that are supplied to you.

• If you are planning to recycle the front cover, follow the instructions in “Disassemble the front cover for

recycle” on page 268 for compliance with local regulations.

Install the front cover

Install the front cover by sliding the cover into position and pressing until it is fully seated.

Complete the following steps to install the front cover:

Watch the procedure

. A video of the replacement process is available:

•

YouTube

•

Youku

132

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы:

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, Руководство пользователя, Страница: 142 / 296

Результаты поиска

Содержание ThinkAgile VX 4-Socket 4U Certified Node

Отзывы: