Lenovo ThinkAgile VX 4-Socket 4U Certified Node Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 296

background image

Figure 62. Fan removal

Step 1. Press the fan handle inward toward the center of the server to release the latch; then, pull the fan

forward halfway (see Figure 62 “Fan removal” on page 120), and wait 10 seconds.

Step 2. Pull the fan forward and out of the server. The fan is connected to the fan handle via a hinge and

the fan will flop downward when it is removed from the server.

To maintain system cooling, all fans must be installed in the server during operation.

If you are instructed to return the fan, follow all packaging instructions, and use any packaging materials for
shipping that are supplied to you.

Install the fan

Insert the fan in the front of the chassis; then, push it in until it stops and the latch engages. Fans are hot-

swap devices that can be installed while the server is powered on.

S017

CAUTION:
Hazardous moving fan blades nearby. Keep fingers and other body parts away.

Note:

The ThinkAgile VX7820 Appliance/VX 4U Certified Node supports two types of internal hot-swap fan

(a 16K fan and a 19K fan). Make sure that the fan being installed is the same type as the fan that was
removed. Different fan types cannot be mixed within a system.

Complete the following steps to install a fan:

120

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

«
...
128
129
130
131
132
...
»

Содержание ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkAgile VX 4-Socket 4U Certified Node

Enterprise Server S80

Бренд: IBM Страницы: 282

Бренд: Gateway Страницы: 26

Бренд: IBM Страницы: 200

Бренд: Fujitsu Siemens Computers Страницы: 68

Netfinity 3500 Series

Бренд: IBM Страницы: 152

ProtectServer External 2

Бренд: SafeNet Страницы: 22

Бренд: W&T Страницы: 228

Бренд: RackSolutions Страницы: 8

Бренд: IBM Страницы: 48

callpilot 1002rp

Бренд: Avaya Страницы: 150

Бренд: Olive Страницы: 103

UniServer R4300 G6

Бренд: H3C Страницы: 542

Eternus DX80 S2

Бренд: Fujitsu Страницы: 186

Бренд: Fujitsu Страницы: 242

Бренд: Gigabyte Страницы: 108

Бренд: National Instruments Страницы: 4

Xtreme PC NG6450

Бренд: Chip PC Страницы: 4

SocketEthernetIP EN60601

Бренд: Multitech Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды