Lenovo NeXtScale nx360 M4, Инструкция по установке и обслуживанию

Страница: 68 / 738

• POST event log: This log contains the most recent error codes and messages that were generated during
POST. You can view the contents of the POST event log from the Setup utility (see “Starting the Setup
utility” on page 25). For more information about POST error codes, see Appendix B “UEFI (POST) error
codes” on page 525.
• System-event log: This log contains POST and system management interrupt (SMI) events and all
events that are generated by the baseboard management controller that is embedded in the integrated
management module (IMM). You can view the contents of the system-event log through the Setup
utility and through the Dynamic System Analysis (DSA) program (as IPMI event log).The system-event
log is limited in size. When it is full, new entries will not overwrite existing entries; therefore, you must
periodically clear the system-event log through the Setup utility. When you are troubleshooting an error,
you might have to save and then clear the system-event log to make the most recent events available for
analysis. For more information about the system-event log, see Appendix A “Integrated Management
Module II (IMM2) error messages” on page 179.
Messages are listed on the left side of the screen, and details about the selected message are displayed
on the right side of the screen. To move from one entry to the next, use the Up Arrow (
↑
) and Down
Arrow (
↓
) keys.
Some IMM sensors cause assertion events to be logged when their setpoints are reached. When a
setpoint condition no longer exists, a corresponding deassertion event is logged. However, not all events
are assertion-type events.
• Integrated management module II (IMM2) event log: This log contains a filtered subset of all IMM,
POST, and system management interrupt (SMI) events. You can view the IMM event log through the IMM
web interface. For more information, see “Logging on to the web interface” on page 34. You can also
view the IMM event log through the Dynamic System Analysis (DSA) program (as the ASM event log).
For more information about IMM error messages, see Appendix A “Integrated Management Module II
(IMM2) error messages” on page 179.
• DSA event log: This log is generated by the Dynamic System Analysis (DSA) program, and it is a
chronologically ordered merge of the system-event log (as the IPMI event log), the IMM chassis-event log
(as the ASM event log), and the operating-system event logs. You can view the DSA event log through the
DSA program (see “Viewing event logs without restarting the server” on page 54). For more information
about DSA and DSA messages, see “IBM Dynamic System Analysis” on page 56 and Appendix C “DSA
diagnostic test results” on page 549.
Viewing event logs through the Setup utility
To view the POST event log or system-event log, complete the following steps:
Step 1. Turn on the server.
Step 2. When the prompt
<F1> Setup
is displayed, press
F1
. If you have set both a power-on password and
an administrator password, you must type the administrator password to view the event logs.
Step 3. Select System Event Logs and use one of the following procedures:
• To view the POST event log, select POST Event Viewers .
• To view the system-event log, select System Event Log .
Viewing event logs without restarting the server
If the server is not hung and the IMM is connected to a network, methods are available for you to view one or
more event logs without having to restart the server.
If you have installed Dynamic System Analysis (DSA) Portable, you can use it to view the system-event log
(as the IPMI event log), or the IMM event log (as the ASM event log), the operating-system event logs, or the
merged DSA log. You can also use DSA Preboot to view these logs, although you must restart the server to
use DSA Preboot. To install DSA Portable or check for and download a later version of DSA Preboot CD
image, go to http://www.ibm.com/support/entry/portal/docdisplay?lndocid=SERV-DSA.
54
IBM NeXtScale nx360 M4 Installation and Service Guide