Lenovo HX3510-G Скачать руководство пользователя страница 1087

Страница: 1087 / 1240

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

089-901-000 : CPU Stress Test Failed

CPU Stress Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. If the system has stopped responding, turn off and restart the system and then run the test again.

2. Make sure that the DSA Diagnostic code is at the latest level.

3. Run the test again.

4. Check system firmware level and upgrade if necessary. The installed firmware level can be found

in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

5. Run the test again.

6. If the system has stopped responding, turn off and restart the system and then run the test again.

7. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA Emulex adapter test results

The following messages can result when you run the Emulex adapter test.

Test results for the DSA Emulex adapter test

The following messages can result when you run the DSA Emulex adapter test.

•

516-000-000 : ELXUCNA: NIC MAC LoopBackTest Passed

Appendix C. DSA diagnostic test results

1075

«
...
1085
1086
1087
1088
1089
...
»

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды