Lenovo HX3510-G Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 1240

background image

Step 16. Reset the CMOS by removing the coin-cell battery (also called CMOS battery). See “Removing

the coin-cell battery (also called CMOS battery)” on page 189.

Step 17. Leave the coin-cell battery out of the server for approximately 5 to 15 minutes.

Step 18. Reinstall the coin-cell battery (see “Replacing the coin-cell battery (also called CMOS battery)” on

Step 19. Reinstall the top cover (see “Replacing the top cover” on page 118).

Step 20. Reconnect the power cord and any cables that you removed.

Step 21. Restart the server. The system begins the power-on self-test (POST).

Step 22. If these recovery efforts fail, contact your service representative for support.

In-band automated boot recovery method

This section details the in-band automated boot recovery method.

Note:

Use this method if the BOARD LED on the light path diagnostics panel is lit and there is a log entry

or

Booting Backup Image

is displayed on the firmware splash screen; otherwise, use the in-band manual

recovery method.

Step 1.

Boot the server to an operating system that is supported by the firmware update package that
you downloaded.

Step 2.

Perform the firmware update by following the instructions that are in the firmware update package
readme file.

Step 3.

Restart the server.

Step 4.

At the firmware splash screen, press F3 when prompted to restore to the primary bank. The
server boots from the primary bank.

Out-of-band method

See the IMM2 documentation (

Integrated Management Module II User's Guide

) at

http://publib.boulder.ibm.com/infocenter/ systemx/documentation/topic/ com.lenovo.sysx.imm2.doc/
printable_doc.html.

Automated boot recovery (ABR)

Use this information for Automated boot recovery (ABR).

While the server is starting, if the integrated management module II detects problems with the server
firmware in the primary bank, the server automatically switches to the backup firmware bank and gives
you the opportunity to recover the firmware in the primary bank. For instructions for recovering the UEFI
firmware, see “Recovering the server firmware (UEFI update failure)” on page 86. After you have recovered
the firmware in the primary bank, complete the following steps:

Step 1.

Restart the server.

Step 2.

When the prompt

Press F3 to restore to primary

is displayed, press F3 to start the server from

the primary bank.

Nx-boot failure

Use this information for Nx-boot failure.

88

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

«
...
98
99
100
101
102
...
»

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HX3510-G

Бренд: IBM Страницы: 908

Бренд: IBM Страницы: 66

FusionServer G8600 V7

Бренд: xFusion Digital Technologies Страницы: 112

SUPERSERVER 6015C-NT

Бренд: Supermicro Страницы: 110

Бренд: Data-Tronix Страницы: 29

Бренд: Data-Tronix Страницы: 30

Бренд: Epson Страницы: 28

EpsonNet 802.11b

Бренд: Epson Страницы: 30

Stylus C80WN - Ink Jet Printer

Бренд: Epson Страницы: 1

Бренд: Epson Страницы: 258

Бренд: Epson Страницы: 280

Бренд: disguise Страницы: 12

Бренд: IBM Страницы: 16

AcquiLite A7810

Бренд: Obvius Страницы: 29

ServTray KVT201A-JP-R3

Бренд: Black Box Страницы: 18

AirProjector KJ-200

Бренд: TriLink Страницы: 56

Express5800/140Hf

Бренд: NEC Страницы: 482

Бренд: Meinberg Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды