Lenovo DM120S Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 70

Lenovo DM120S Скачать руководство пользователя страница 9

If...

Then...

You are cabling a multipath HA, multipath,
single-path HA, or single-path configuration

Cable the shelf-to-shelf connections as
“standard” connectivity (using IOM ports 3 and
1):

a. Beginning with the logical first shelf in the
stack, connect IOM A port 3 to the next shelf's
IOM A port 1 until each IOM A in the stack is
connected.

b. Repeat substep a for IOM B.

c. Repeat substeps a and b for each stack.

You are cabling a quad-path HA or quad-path
configuration

Cable the shelf-to-shelf connections as
“double-wide” connectivity:

You cable the standard connectivity using IOM
ports 3 and 1 and then the double-wide
connectivity using IOM ports 4 and 2.

a. Beginning with the logical first shelf in the
stack, connect IOM A port 3 to the next shelf's
IOM A port 1 until each IOM A in the stack is
connected.

b. Beginning with the logical first shelf in the
stack, connect IOM A port 4 to the next shelf's
IOM A port 2 until each IOM A in the stack is
connected.

c. Repeat substeps a and b for IOM B.

d. Repeat substeps a through c for each stack.

Step 2. Identify the controller SAS port pairs that you can use to cable the controller-to-stack connections.

a. Check the controller-to-stack cabling worksheets and cabling examples sections to see

whether a completed worksheet exists for your configuration.

b. The next step depends on whether a completed worksheet exists for your configuration:

If...

Then...

There is a completed worksheet for
your configuration

Go to the next step.

You use the existing completed worksheet.

There is no completed worksheet for
your configuration

Fill out a controller-to-stack cabling worksheet template.

Worksheet templates can be found towards the back of this
guide.

Step 3.

Cable the controller-to-stack connections using the completed worksheet.

Installing and cabling disk shelves with IOM12 modules for a new system installation

5

«
...
7
8
9
10
11
...
»

Содержание DM120S







































































Отзывы:

Нет отзывов